McAfee Secure

Exam Code: NSE5_FSW_AD-7.6

Exam Name: Fortinet NSE 5 - FortiSwitch 7.6 Administrator

Certification Provider: Fortinet

Corresponding Certification: NSE5

Fortinet NSE5_FSW_AD-7.6 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

64 Questions & Answers with Testing Engine

"Fortinet NSE 5 - FortiSwitch 7.6 Administrator Exam", also known as NSE5_FSW_AD-7.6 exam, is a Fortinet certification exam.

Pass your tests with the always up-to-date NSE5_FSW_AD-7.6 Exam Engine. Your NSE5_FSW_AD-7.6 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Fortinet NSE5_FSW_AD-7.6 Practice Test 44

Question 430

At the Glenbrook regional network integrator, an organization plans switch-controller NAC enforcement on a remote FortiLink over Layer 3 island. Which explanation best accounts for the concern?

  1. Split-interface redundancy intentionally limits active forwarding until a supported MCLAG state permits more
  2. Separate VLAN labels do not independently guarantee tenant Layer 3 policy isolation
  3. FortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design
  4. Manual per-device setup increases configuration drift and delays consistent provisioning

Explanation

Correct Answer

C:

The situation shows that fortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design, rather than merely a monitoring or presentation issue. Remediation is to choose a supported deployment or alternate enforcement design rather than assuming FortiSwitch NAC functions over Layer 3.

Incorrect Answers

A:

The offered principle is: Split-interface redundancy intentionally limits active forwarding until a supported MCLAG state permits more. In the source material it is associated with: Split-interface redundancy intentionally limits active forwarding until a supported MCLAG state permits more. This case has a different controlling cause: FortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design. Its keyed mechanism is: FortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design.

B:

Although separate VLAN labels do not independently guarantee tenant Layer 3 policy isolation, the presented symptoms do not support that as the primary cause; they indicate that fortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design. For the Glenbrook regional network integrator, the direct corrective action is to choose a supported deployment or alternate enforcement design rather than assuming FortiSwitch NAC functions over Layer 3.

D:

Manual per-device setup increases configuration drift and delays consistent provisioning. That may occur elsewhere, but the evidence at the Glenbrook regional network integrator instead points to the fact that fortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design.

Question 431

At the Glenbrook regional network integrator, an organization plans switch-controller NAC enforcement on a remote FortiLink over Layer 3 island. Which test result best shows the requirement is met?

  1. A test discovers both switches over the corrected point-to-point transport
  2. A review confirms chosen enforcement works without reliance on unsupported NAC behavior
  3. Each tenant traffic tag remains distinct and only its policy-controlled path works
  4. Each authorized switch obtains a distinct working management address and stays connected

Explanation

Correct Answer

B:

This is the relevant acceptance result: a review confirms chosen enforcement works without reliance on unsupported NAC behavior. It demonstrates the outcome of choosing to choose a supported deployment or alternate enforcement design rather than assuming FortiSwitch NAC functions over Layer 3.

Incorrect Answers

A:

A test discovers both switches over the corrected point-to-point transport. That result would test a control for this other failure: Mismatched provider tag EtherType can prevent expected encapsulated control traffic delivery. The question instead requires evidence for: FortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design. The direct outcome to verify is: A review confirms chosen enforcement works without reliance on unsupported NAC behavior.

C:

Each tenant traffic tag remains distinct and only its policy-controlled path works. That result would test a control for this other failure: Physical port sharing and VLAN ownership across VDOMs require deliberate controller configuration. The question instead requires evidence for: FortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design. The direct outcome to verify is: A review confirms chosen enforcement works without reliance on unsupported NAC behavior.

D:

At the Glenbrook regional network integrator, a result about fortilink interface address pool would not show that the team corrected the failure where fortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design.

Question 432

At the Glenbrook regional network integrator, an organization plans switch-controller NAC enforcement on a remote FortiLink over Layer 3 island. Which ongoing control best prevents this issue from recurring?

  1. Check FortiLink Layer 3 feature limits before new security integrations
  2. Reassess topology only when availability requirements grow
  3. Audit VLAN references and port exports after VDOM restructuring
  4. Audit administration protocols and source restrictions routinely

Explanation

Correct Answer

A:

The continuing safeguard is to check FortiLink Layer 3 feature limits before new security integrations. It helps avoid the original condition: fortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design.

Incorrect Answers

B:

Reassess topology only when availability requirements grow. That safeguard would help prevent recurrence of: A simple managed site can be operated without unnecessary high-availability interconnections. The risk being reviewed here is instead: FortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design. The matching ongoing control is: Check FortiLink Layer 3 feature limits before new security integrations.

C:

Audit VLAN references and port exports after VDOM restructuring is not the primary recurring safeguard for this problem. The team should check FortiLink Layer 3 feature limits before new security integrations. For the Glenbrook regional network integrator, the direct corrective action is to choose a supported deployment or alternate enforcement design rather than assuming FortiSwitch NAC functions over Layer 3.

D:

Audit administration protocols and source restrictions routinely. That safeguard would help prevent recurrence of: Open management access from untrusted segments broadens credential attack surface. The risk being reviewed here is instead: FortiSwitch NAC is not supported in the documented FortiLink over Layer 3 island design. The matching ongoing control is: Check FortiLink Layer 3 feature limits before new security integrations.

Question 433

At the Thornfield multisite IT support team, engineers connect several FortiSwitch units behind one remote mgmt-port Layer 3 management uplink and expect a managed island. Which implementation choice best addresses the situation?

  1. Use supported FortiLink point-to-point Layer 2 bridging and appropriate discovery handling
  2. Resize and validate the supported FortiLink management address pool or topology addressing plan
  3. Apply a supported learning limit on eligible shared FortiSwitch ports and plan valid capacity
  4. Follow supported management-port Layer 3 design limits or use an appropriate in-band topology

Explanation

Correct Answer

D:

The primary failure mode is that the documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The proposed action directly fixes it by requiring the team to follow supported management-port Layer 3 design limits or use an appropriate in-band topology; afterward, verify that a supported test topology brings the intended switch online without unsupported downstream stacking.

Incorrect Answers

A:

This alternative would be suitable where some intermediate Layer 2 devices do not transport standard neighbor discovery frames. It does not by itself resolve the need to follow supported management-port Layer 3 design limits or use an appropriate in-band topology. For the Thornfield multisite IT support team, the direct corrective action is to follow supported management-port Layer 3 design limits or use an appropriate in-band topology.

B:

Resize and validate the supported FortiLink management address pool or topology addressing plan addresses a different kind of problem: switch discovery and controller communication require nonconflicting usable management addresses. Here the reported weakness is that the documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. For the Thornfield multisite IT support team, the direct corrective action is to follow supported management-port Layer 3 design limits or use an appropriate in-band topology.

C:

The option addresses the separate situation where unbounded MAC learning can strain forwarding resources and cross-tenant expectations. For this case, the more appropriate response is to follow supported management-port Layer 3 design limits or use an appropriate in-band topology. For the Thornfield multisite IT support team, the direct corrective action is to follow supported management-port Layer 3 design limits or use an appropriate in-band topology.

Question 434

At the Thornfield multisite IT support team, engineers connect several FortiSwitch units behind one remote mgmt-port Layer 3 management uplink and expect a managed island. What risk should the team identify as the primary issue?

  1. A configured backup interface does not prove switch management survives an upstream path outage
  2. The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member
  3. Unreviewed automatic authorization can admit a connected switch before identity and installation are checked
  4. The documented shared FortiSwitch port feature set does not include DHCP snooping

Explanation

Correct Answer

B:

This identifies the root issue: the documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. At the Thornfield multisite IT support team, the team should therefore follow supported management-port Layer 3 design limits or use an appropriate in-band topology.

Incorrect Answers

A:

The offered action is: A configured backup interface does not prove switch management survives an upstream path outage. It is associated with this separate technical condition: A configured backup interface does not prove switch management survives an upstream path outage. The actual incident concerns a different dependency: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The corresponding change is: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member.

C:

The offered alternative is: Unreviewed automatic authorization can admit a connected switch before identity and installation are checked. It addresses this separate failure mode: Unreviewed automatic authorization can admit a connected switch before identity and installation are checked. In the current case, the observed mechanism is: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The keyed action, The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member., targets that condition more directly.

D:

The documented shared FortiSwitch port feature set does not include DHCP snooping. That is not the mechanism that accounts for the stated failure at the Thornfield multisite IT support team.

Question 435

At the Thornfield multisite IT support team, engineers connect several FortiSwitch units behind one remote mgmt-port Layer 3 management uplink and expect a managed island. What is the strongest acceptance test for this change?

  1. The island stays manageable during supported single-peer link member tests
  2. A supported test topology brings the intended switch online without unsupported downstream stacking
  3. A test tenant authentication policy works without enabling unsupported port features
  4. Both tenants' critical endpoints remain powered in the approved full-load test

Explanation

Correct Answer

B:

The team can confirm the fix by showing that a supported test topology brings the intended switch online without unsupported downstream stacking. This aligns with the corrective design to follow supported management-port Layer 3 design limits or use an appropriate in-band topology.

Incorrect Answers

A:

The island stays manageable during supported single-peer link member tests. That result would test a control for this other failure: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The question instead requires evidence for: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The direct outcome to verify is: A supported test topology brings the intended switch online without unsupported downstream stacking.

C:

A test tenant authentication policy works without enabling unsupported port features. That result would test a control for this other failure: Multi-VDOM shared ports expose a defined subset of switch security capabilities. The question instead requires evidence for: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The direct outcome to verify is: A supported test topology brings the intended switch online without unsupported downstream stacking.

D:

The offered observation is: Both tenants' critical endpoints remain powered in the approved full-load test. It would support the separate mechanism: Virtual tenant separation does not create independent physical power supplies. In this case the decisive dependency is: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The original keyed verification is: A supported test topology brings the intended switch online without unsupported downstream stacking.

Question 436

At the Thornfield multisite IT support team, engineers connect several FortiSwitch units behind one remote mgmt-port Layer 3 management uplink and expect a managed island. Which setting or practice should be reviewed in future?

  1. Review L3 island route and LAG support during redundancy changes
  2. Validate port-specific topology constraints before branch construction
  3. Review tenant device forecasts before increasing limits
  4. Maintain a tested FortiOS and FortiSwitchOS version matrix

Explanation

Correct Answer

B:

This control works beyond the initial remediation because it requires the team to validate port-specific topology constraints before branch construction.

Incorrect Answers

A:

Review L3 island route and LAG support during redundancy changes is not the primary recurring safeguard for this problem. The team should validate port-specific topology constraints before branch construction. For the Thornfield multisite IT support team, the direct corrective action is to follow supported management-port Layer 3 design limits or use an appropriate in-band topology.

C:

The suggested preventive check is: Review tenant device forecasts before increasing limits. Its technical scope concerns: Unbounded MAC learning can strain forwarding resources and cross-tenant expectations. This question asks how to sustain control over: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The more targeted safeguard is: Validate port-specific topology constraints before branch construction.

D:

Maintain a tested FortiOS and FortiSwitchOS version matrix. That safeguard would help prevent recurrence of: Firmware version mismatches can break expected FortiLink and feature operation. The risk being reviewed here is instead: The documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. The matching ongoing control is: Validate port-specific topology constraints before branch construction.

Question 437

At the Highbridge campus infrastructure group, an island FortiSwitch aggregates ports toward two different intermediary routers while using internal-interface Layer 3 management. Which corrective action best meets the requirement?

  1. Follow supported management-port Layer 3 design limits or use an appropriate in-band topology
  2. Rework the LAG to the supported single intermediary or supported alternative topology
  3. Export supported FortiSwitch ports to the correct tenant VDOM with explicit ownership
  4. Validate the Fortinet compatibility guidance and stage supported switch firmware upgrades from the management controller

Explanation

Correct Answer

B:

The primary failure mode is that the documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The proposed action directly fixes it by requiring the team to rework the LAG to the supported single intermediary or supported alternative topology; afterward, verify that the island stays manageable during supported single-peer link member tests.

Incorrect Answers

A:

The option addresses the separate situation where the documented out-of-band mgmt-port Layer 3 mode supports a single FortiSwitch island member. For this case, the more appropriate response is to rework the LAG to the supported single intermediary or supported alternative topology. For the Highbridge campus infrastructure group, the direct corrective action is to rework the LAG to the supported single intermediary or supported alternative topology.

C:

Export supported FortiSwitch ports to the correct tenant VDOM with explicit ownership can be useful for another FortiSwitch 7.6 administration workflow, but it leaves the immediate failure unresolved. Here the priority is to rework the LAG to the supported single intermediary or supported alternative topology. For the Highbridge campus infrastructure group, the direct corrective action is to rework the LAG to the supported single intermediary or supported alternative topology.

D:

The offered alternative is: Validate the Fortinet compatibility guidance and stage supported switch firmware upgrades from the management controller. It addresses this separate failure mode: Firmware version mismatches can break expected FortiLink and feature operation. In the current case, the observed mechanism is: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The keyed action, Rework the LAG to the supported single intermediary or supported alternative topology., targets that condition more directly.

Question 438

At the Highbridge campus infrastructure group, an island FortiSwitch aggregates ports toward two different intermediary routers while using internal-interface Layer 3 management. Which underlying issue most directly explains this situation?

  1. Some intermediate Layer 2 devices do not transport standard neighbor discovery frames
  2. The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers
  3. Unbounded MAC learning can strain forwarding resources and cross-tenant expectations
  4. Physical managed FortiSwitch inventory may reside in the controlling VDOM rather than every tenant

Explanation

Correct Answer

B:

The architectural weakness is that the documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. It can be addressed through the controlled change to rework the LAG to the supported single intermediary or supported alternative topology.

Incorrect Answers

A:

The offered principle is: Some intermediate Layer 2 devices do not transport standard neighbor discovery frames. In the source material it is associated with: Some intermediate Layer 2 devices do not transport standard neighbor discovery frames. This case has a different controlling cause: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. Its keyed mechanism is: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers.

C:

The offered principle is: Unbounded MAC learning can strain forwarding resources and cross-tenant expectations. In the source material it is associated with: Unbounded MAC learning can strain forwarding resources and cross-tenant expectations. This case has a different controlling cause: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. Its keyed mechanism is: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers.

D:

Although physical managed FortiSwitch inventory may reside in the controlling VDOM rather than every tenant, the presented symptoms do not support that as the primary cause; they indicate that the documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. For the Highbridge campus infrastructure group, the direct corrective action is to rework the LAG to the supported single intermediary or supported alternative topology.

Question 439

At the Highbridge campus infrastructure group, an island FortiSwitch aggregates ports toward two different intermediary routers while using internal-interface Layer 3 management. What evidence would justify considering this concern addressed?

  1. The island remains managed while an L2 broadcast remains local to its site
  2. The island stays manageable during supported single-peer link member tests
  3. The approved number of learned addresses works and excess sources follow policy
  4. An approved factory-reset switch receives the correct managed inventory and site policy

Explanation

Correct Answer

B:

The intended correction is to rework the LAG to the supported single intermediary or supported alternative topology. The decisive verification is that the island stays manageable during supported single-peer link member tests, rather than only confirming configuration was saved.

Incorrect Answers

A:

The island remains managed while an L2 broadcast remains local to its site. That result would test a control for this other failure: FortiLink over Layer 3 does not create a continuous Layer 2 VLAN across the routed path. The question instead requires evidence for: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The direct outcome to verify is: The island stays manageable during supported single-peer link member tests.

C:

The approved number of learned addresses works and excess sources follow policy. That result would test a control for this other failure: Unbounded MAC learning can strain forwarding resources and cross-tenant expectations. The question instead requires evidence for: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The direct outcome to verify is: The island stays manageable during supported single-peer link member tests.

D:

The offered observation is: An approved factory-reset switch receives the correct managed inventory and site policy. It would support the separate mechanism: Manual per-device setup increases configuration drift and delays consistent provisioning. In this case the decisive dependency is: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The original keyed verification is: The island stays manageable during supported single-peer link member tests.

Question 440

At the Highbridge campus infrastructure group, an island FortiSwitch aggregates ports toward two different intermediary routers while using internal-interface Layer 3 management. How should the organization sustain the improvement?

  1. Include managed switching in FortiGate HA acceptance tests
  2. Audit management addresses and access-source restrictions
  3. Synchronize switch port inventory after moves
  4. Review L3 island route and LAG support during redundancy changes

Explanation

Correct Answer

D:

The needed prevention is to review L3 island route and LAG support during redundancy changes. It directly sustains the original change to rework the LAG to the supported single intermediary or supported alternative topology.

Incorrect Answers

A:

The suggested preventive check is: Include managed switching in FortiGate HA acceptance tests. Its technical scope concerns: Failing over the firewall does not help if the promoted member lacks an operational FortiLink path. This question asks how to sustain control over: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The more targeted safeguard is: Review L3 island route and LAG support during redundancy changes.

B:

Audit management addresses and access-source restrictions. That safeguard would help prevent recurrence of: Management-plane routing and access controls are separate from user data forwarding. The risk being reviewed here is instead: The documented Layer 3 FortiLink in-band LAG cannot span separate intermediary routers. The matching ongoing control is: Review L3 island route and LAG support during redundancy changes.

C:

That routine supports fortiswitch port inventory labels, but the relevant ongoing risk requires the team to review L3 island route and LAG support during redundancy changes. For the Highbridge campus infrastructure group, the direct corrective action is to rework the LAG to the supported single intermediary or supported alternative topology.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests