McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 1

Question 1

At fictional Riverstone Travel, a network engineer supporting booking offices is reviewing IS-IS level-aware topology and database synchronization during a new network integration (HCIP-H12-821-ISIS-001). The observed network issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. Which next engineering action best addresses the reported problem?

  1. Confirm the expected nearest Level 1/2 border route and associated default or leaking policy.
  2. Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions.
  3. Permit the appropriate IS-IS link-layer PDUs and check physical segment connectivity.
  4. Examine the L1/L2 router's attached-state behavior and desired inter-area default routing.

Explanation

Correct Answer

B:

The directly responsive action is: Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions. The specific reported fault is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. Confirmation should show: The point-to-point link forms the correct adjacency without a pseudonode LSP. The supporting technical principle is: IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.

Incorrect Answers

A:

“Confirm the expected nearest Level 1/2 border route and associated default or leaking policy” responds to another technical or business failure: A Level 1-only router cannot reach an IP prefix advertised only outside its local IS-IS area. That source case depends on: IS-IS Level 1 routing has area-local visibility and relies on Level 2 interarea reachability. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions” because IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.

C:

“Permit the appropriate IS-IS link-layer PDUs and check physical segment connectivity” responds to another technical or business failure: IS-IS adjacency remains Down when Hello frames are filtered by an intermediate layer-2 device. That source case depends on: IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions” because IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.

D:

“Examine the L1/L2 router's attached-state behavior and desired inter-area default routing” responds to another technical or business failure: An IS-IS Level 1 router gets an unwanted default path after an L1/L2 node reports reachability to other areas. That source case depends on: IS-IS attached-bit behavior can influence Level 1 routing toward other areas. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions” because IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.

Question 2

At fictional Riverstone Travel, a network engineer supporting booking offices is reviewing IS-IS level-aware topology and database synchronization during a new network integration (HCIP-H12-821-ISIS-001). The observed network issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. Which routing, switching, or network principle best explains the appropriate solution?

  1. IS-IS adjacency level selection determines which databases neighbors can share.
  2. An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.
  3. IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.
  4. IS-IS wide metrics extend usable cost representation for modern network designs.

Explanation

Correct Answer

C:

The governing principle is: IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement. In this scenario, the appropriate action is: Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions. Valid evidence would show: The point-to-point link forms the correct adjacency without a pseudonode LSP.

Incorrect Answers

A:

“IS-IS adjacency level selection determines which databases neighbors can share” responds to another technical or business failure: Two Level 2 IS-IS routers do not form neighbors because one interface is configured for Level 1-only adjacencies. That source case depends on: IS-IS adjacency level selection determines which databases neighbors can share. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement” because IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.

B:

“An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised” responds to another technical or business failure: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. That source case depends on: An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement” because IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.

D:

“IS-IS wide metrics extend usable cost representation for modern network designs” responds to another technical or business failure: A large IS-IS deployment uses narrow metrics until a new path cost exceeds the legacy representable range. That source case depends on: IS-IS wide metrics extend usable cost representation for modern network designs. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement” because IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.

Question 3

At fictional Riverstone Travel, a network engineer supporting booking offices is reviewing IS-IS level-aware topology and database synchronization during a new network integration (HCIP-H12-821-ISIS-001). The observed network issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. Which ongoing preventive or detective control would best reduce recurrence?

  1. Include actual circuit topology and type in ISIS troubleshooting checks.
  2. Compare circuit-type values during core link acceptance.
  3. Test default reachability from every Level 1 access area.
  4. Review leaked-prefix counts during Level 1 and Level 2 changes.

Explanation

Correct Answer

A:

The preventive or detective safeguard is: Include actual circuit topology and type in ISIS troubleshooting checks. This directly addresses the recurring fault: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The corrective action would be: Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions. Success is demonstrated when: The point-to-point link forms the correct adjacency without a pseudonode LSP.

Incorrect Answers

B:

“Compare circuit-type values during core link acceptance” addresses recurrence of another problem: Two Level 2 IS-IS routers do not form neighbors because one interface is configured for Level 1-only adjacencies. That problem depends on: The preventive or detective safeguard is: Compare circuit-type values during core link acceptance. The recurring risk here is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more targeted safeguard is “Include actual circuit topology and type in ISIS troubleshooting checks” because the preventive or detective safeguard is: Include actual circuit topology and type in ISIS troubleshooting checks.

C:

“Test default reachability from every Level 1 access area” addresses recurrence of another problem: A Level 1-only router cannot reach an IP prefix advertised only outside its local IS-IS area. That problem depends on: The preventive or detective safeguard is: Test default reachability from every Level 1 access area. The recurring risk here is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more targeted safeguard is “Include actual circuit topology and type in ISIS troubleshooting checks” because the preventive or detective safeguard is: Include actual circuit topology and type in ISIS troubleshooting checks.

D:

“Review leaked-prefix counts during Level 1 and Level 2 changes” addresses recurrence of another problem: An engineer leaks all Level 2 routes into Level 1 and overwhelms a branch routing table. That problem depends on: The preventive or detective safeguard is: Review leaked-prefix counts during Level 1 and Level 2 changes. The recurring risk here is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more targeted safeguard is “Include actual circuit topology and type in ISIS troubleshooting checks” because the preventive or detective safeguard is: Include actual circuit topology and type in ISIS troubleshooting checks.

Question 4

At fictional Riverstone Travel, a network engineer supporting booking offices is reviewing IS-IS level-aware topology and database synchronization during a new network integration (HCIP-H12-821-ISIS-001). The observed network issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. Which observation most directly verifies that the corrective change succeeded?

  1. The point-to-point link forms the correct adjacency without a pseudonode LSP.
  2. Neighbor databases show distinct system IDs and consistent LSP origins.
  3. The elected DIS originates the expected pseudonode and other routers form correct LAN adjacencies.
  4. An eligible Level 1 neighbor forms in the expected common area.

Explanation

Correct Answer

A:

The best verification observation is: The point-to-point link forms the correct adjacency without a pseudonode LSP. It demonstrates the corrective action: Configure the actual point-to-point circuit type and validate neighbor behavior without DIS assumptions. This fits the principle: IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement. Verify on the actual Huawei platform and network release.

Incorrect Answers

B:

“Neighbor databases show distinct system IDs and consistent LSP origins” responds to another technical or business failure: An IS-IS configuration reuses one system ID on two distinct routers and link-state advertisements become ambiguous. That source case depends on: The best verification observation is: Neighbor databases show distinct system IDs and consistent LSP origins. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “The point-to-point link forms the correct adjacency without a pseudonode LSP” because the best verification observation is: The point-to-point link forms the correct adjacency without a pseudonode LSP.

C:

“The elected DIS originates the expected pseudonode and other routers form correct LAN adjacencies” responds to another technical or business failure: An IS-IS router is elected designated intermediate system on an Ethernet segment but an engineer calls it an OSPF DR. That source case depends on: The best verification observation is: The elected DIS originates the expected pseudonode and other routers form correct LAN adjacencies. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “The point-to-point link forms the correct adjacency without a pseudonode LSP” because the best verification observation is: The point-to-point link forms the correct adjacency without a pseudonode LSP.

D:

“An eligible Level 1 neighbor forms in the expected common area” responds to another technical or business failure: Two Huawei routers share a link but their IS-IS NET addresses use different area identifiers while both are configured as Level 1. That source case depends on: The best verification observation is: An eligible Level 1 neighbor forms in the expected common area. The present issue is: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. The more direct action is “The point-to-point link forms the correct adjacency without a pseudonode LSP” because the best verification observation is: The point-to-point link forms the correct adjacency without a pseudonode LSP.

Question 5

At fictional Uplands Retail, a network engineer supporting customer edge routers is reviewing IGMP and PIM multicast distribution during an intersite service activation (HCIP-H12-821-MULTICAST-002). The observed network issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. Which routing, switching, or network principle best explains the appropriate solution?

  1. SSM receivers identify the source and group and avoid general ASM RP discovery.
  2. IGMP uses membership queries and reports to maintain receiver state.
  3. IGMP leave handling and query responses govern expiry of membership state.
  4. Multicast routing uses reverse-path-forwarding checks to prevent loops.

Explanation

Correct Answer

D:

The governing principle is: Multicast routing uses reverse-path-forwarding checks to prevent loops. In this scenario, the appropriate action is: Correct unicast route reachability or multicast RPF path so the incoming interface is valid. Valid evidence would show: Packets arrive on the expected RPF interface and are forwarded downstream.

Incorrect Answers

A:

“SSM receivers identify the source and group and avoid general ASM RP discovery” responds to another technical or business failure: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. That source case depends on: SSM receivers identify the source and group and avoid general ASM RP discovery. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Multicast routing uses reverse-path-forwarding checks to prevent loops” because Multicast routing uses reverse-path-forwarding checks to prevent loops.

B:

“IGMP uses membership queries and reports to maintain receiver state” responds to another technical or business failure: A multicast router sees no group receivers because IGMP query messages are absent from a VLAN. That source case depends on: IGMP uses membership queries and reports to maintain receiver state. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Multicast routing uses reverse-path-forwarding checks to prevent loops” because Multicast routing uses reverse-path-forwarding checks to prevent loops.

C:

“IGMP leave handling and query responses govern expiry of membership state” responds to another technical or business failure: An IGMPv2 receiver leaves a group but the switch continues forwarding the stream indefinitely. That source case depends on: IGMP leave handling and query responses govern expiry of membership state. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Multicast routing uses reverse-path-forwarding checks to prevent loops” because Multicast routing uses reverse-path-forwarding checks to prevent loops.

Question 6

At fictional Uplands Retail, a network engineer supporting customer edge routers is reviewing IGMP and PIM multicast distribution during an intersite service activation (HCIP-H12-821-MULTICAST-002). The observed network issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. Which observation most directly verifies that the corrective change succeeded?

  1. Multicast packets resume on the revised valid RPF interface after failover.
  2. Packets arrive on the expected RPF interface and are forwarded downstream.
  3. Only intended receivers for each service group see the correct media flow.
  4. Only intended receiver branches obtain a shared group stream with reduced duplicate transmission.

Explanation

Correct Answer

B:

The best verification observation is: Packets arrive on the expected RPF interface and are forwarded downstream. It demonstrates the corrective action: Correct unicast route reachability or multicast RPF path so the incoming interface is valid. This fits the principle: Multicast routing uses reverse-path-forwarding checks to prevent loops. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Multicast packets resume on the revised valid RPF interface after failover” responds to another technical or business failure: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. That source case depends on: The best verification observation is: Multicast packets resume on the revised valid RPF interface after failover. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Packets arrive on the expected RPF interface and are forwarded downstream” because the best verification observation is: Packets arrive on the expected RPF interface and are forwarded downstream.

C:

“Only intended receivers for each service group see the correct media flow” responds to another technical or business failure: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. That source case depends on: The best verification observation is: Only intended receivers for each service group see the correct media flow. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Packets arrive on the expected RPF interface and are forwarded downstream” because the best verification observation is: Packets arrive on the expected RPF interface and are forwarded downstream.

D:

“Only intended receiver branches obtain a shared group stream with reduced duplicate transmission” responds to another technical or business failure: A video stream from one sender is replicated as unicast to hundreds of recipients and saturates the WAN. That source case depends on: The best verification observation is: Only intended receiver branches obtain a shared group stream with reduced duplicate transmission. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Packets arrive on the expected RPF interface and are forwarded downstream” because the best verification observation is: Packets arrive on the expected RPF interface and are forwarded downstream.

Question 7

At fictional Uplands Retail, a network engineer supporting customer edge routers is reviewing IGMP and PIM multicast distribution during an intersite service activation (HCIP-H12-821-MULTICAST-002). The observed network issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. Which next engineering action best addresses the reported problem?

  1. Correlate source RPF, multicast forwarding entry and downstream IGMP or PIM membership.
  2. Enable and validate PIM on all required routed multicast hops in the distribution tree.
  3. Examine leave processing, group-specific queries and membership expiration.
  4. Correct unicast route reachability or multicast RPF path so the incoming interface is valid.

Explanation

Correct Answer

D:

The directly responsive action is: Correct unicast route reachability or multicast RPF path so the incoming interface is valid. The specific reported fault is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. Confirmation should show: Packets arrive on the expected RPF interface and are forwarded downstream. The supporting technical principle is: Multicast routing uses reverse-path-forwarding checks to prevent loops.

Incorrect Answers

A:

“Correlate source RPF, multicast forwarding entry and downstream IGMP or PIM membership” responds to another technical or business failure: An engineer diagnoses multicast stream loss by checking only source packets and ignores outgoing interface list and receiver state. That source case depends on: A working multicast stream requires valid ingress RPF and interested downstream forwarding interfaces. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Correct unicast route reachability or multicast RPF path so the incoming interface is valid” because Multicast routing uses reverse-path-forwarding checks to prevent loops.

B:

“Enable and validate PIM on all required routed multicast hops in the distribution tree” responds to another technical or business failure: A multicast receiver has IGMP state locally but the PIM upstream interface is disabled. That source case depends on: Local IGMP membership alone does not carry multicast across routed PIM boundaries. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Correct unicast route reachability or multicast RPF path so the incoming interface is valid” because Multicast routing uses reverse-path-forwarding checks to prevent loops.

C:

“Examine leave processing, group-specific queries and membership expiration” responds to another technical or business failure: An IGMPv2 receiver leaves a group but the switch continues forwarding the stream indefinitely. That source case depends on: IGMP leave handling and query responses govern expiry of membership state. The present issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more direct action is “Correct unicast route reachability or multicast RPF path so the incoming interface is valid” because Multicast routing uses reverse-path-forwarding checks to prevent loops.

Question 8

At fictional Uplands Retail, a network engineer supporting customer edge routers is reviewing IGMP and PIM multicast distribution during an intersite service activation (HCIP-H12-821-MULTICAST-002). The observed network issue is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. Which ongoing preventive or detective control would best reduce recurrence?

  1. Measure source-tree RPF selection after unicast topology changes.
  2. Audit multicast outgoing-interface lists after receiver churn.
  3. Monitor RPF failures after changing unicast routing metrics.
  4. Test source-route failure recovery for multicast services.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Monitor RPF failures after changing unicast routing metrics. This directly addresses the recurring fault: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The corrective action would be: Correct unicast route reachability or multicast RPF path so the incoming interface is valid. Success is demonstrated when: Packets arrive on the expected RPF interface and are forwarded downstream.

Incorrect Answers

A:

“Measure source-tree RPF selection after unicast topology changes” addresses recurrence of another problem: A PIM-SM router cannot switch efficiently to a shortest-path tree because its source route points through another neighbor. That problem depends on: The preventive or detective safeguard is: Measure source-tree RPF selection after unicast topology changes. The recurring risk here is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more targeted safeguard is “Monitor RPF failures after changing unicast routing metrics” because the preventive or detective safeguard is: Monitor RPF failures after changing unicast routing metrics.

B:

“Audit multicast outgoing-interface lists after receiver churn” addresses recurrence of another problem: An upstream router continuously forwards multicast after a branch has no receivers because PIM prune information is missing. That problem depends on: The preventive or detective safeguard is: Audit multicast outgoing-interface lists after receiver churn. The recurring risk here is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more targeted safeguard is “Monitor RPF failures after changing unicast routing metrics” because the preventive or detective safeguard is: Monitor RPF failures after changing unicast routing metrics.

D:

“Test source-route failure recovery for multicast services” addresses recurrence of another problem: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. That problem depends on: The preventive or detective safeguard is: Test source-route failure recovery for multicast services. The recurring risk here is: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. The more targeted safeguard is “Monitor RPF failures after changing unicast routing metrics” because the preventive or detective safeguard is: Monitor RPF failures after changing unicast routing metrics.

Question 9

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing OSPF area design and link-state convergence during a production cutover (HCIP-H12-821-OSPF-003). The observed network issue is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. Which routing, switching, or network principle best explains the appropriate solution?

  1. OSPF area border routers convey inter-area network reachability using summary information.
  2. OSPF neighbor formation requires matching area configuration on shared links.
  3. OSPF routing exchanges depend on matched authentication parameters when authentication is enabled.
  4. OSPF route installation filtering is not necessarily equivalent to suppressing flooded LSAs.

Explanation

Correct Answer

A:

The governing principle is: OSPF area border routers convey inter-area network reachability using summary information. In this scenario, the appropriate action is: Inspect ABR area connectivity and the Type 3 summary LSAs used for inter-area advertisement. Valid evidence would show: The receiving area learns approved inter-area prefixes through expected summary LSAs.

Incorrect Answers

B:

“OSPF neighbor formation requires matching area configuration on shared links” responds to another technical or business failure: Two neighboring Huawei routers exchange Hello packets but never become OSPF neighbors because their area identifiers differ. That source case depends on: OSPF neighbor formation requires matching area configuration on shared links. The present issue is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. The more direct action is “OSPF area border routers convey inter-area network reachability using summary information” because OSPF area border routers convey inter-area network reachability using summary information.

C:

“OSPF routing exchanges depend on matched authentication parameters when authentication is enabled” responds to another technical or business failure: An OSPF adjacency repeatedly fails due to mismatched authentication algorithms after a maintenance window. That source case depends on: OSPF routing exchanges depend on matched authentication parameters when authentication is enabled. The present issue is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. The more direct action is “OSPF area border routers convey inter-area network reachability using summary information” because OSPF area border routers convey inter-area network reachability using summary information.

D:

“OSPF route installation filtering is not necessarily equivalent to suppressing flooded LSAs” responds to another technical or business failure: An engineer uses a prefix-filter on one OSPF router expecting to prevent every other router from receiving the LSA. That source case depends on: OSPF route installation filtering is not necessarily equivalent to suppressing flooded LSAs. The present issue is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. The more direct action is “OSPF area border routers convey inter-area network reachability using summary information” because OSPF area border routers convey inter-area network reachability using summary information.

Question 10

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing OSPF area design and link-state convergence during a production cutover (HCIP-H12-821-OSPF-003). The observed network issue is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. Which ongoing preventive or detective control would best reduce recurrence?

  1. Compare area IDs in both directions during OSPF adjacency acceptance.
  2. Check duplicate router IDs in configuration reviews and fault diagnostics.
  3. Inspect both LSDB and routing table when evaluating routing-filter controls.
  4. Check inter-area LSA propagation from each ABR after topology changes.

Explanation

Correct Answer

D:

The preventive or detective safeguard is: Check inter-area LSA propagation from each ABR after topology changes. This directly addresses the recurring fault: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. The corrective action would be: Inspect ABR area connectivity and the Type 3 summary LSAs used for inter-area advertisement. Success is demonstrated when: The receiving area learns approved inter-area prefixes through expected summary LSAs.

Incorrect Answers

A:

“Compare area IDs in both directions during OSPF adjacency acceptance” addresses recurrence of another problem: Two neighboring Huawei routers exchange Hello packets but never become OSPF neighbors because their area identifiers differ. That problem depends on: The preventive or detective safeguard is: Compare area IDs in both directions during OSPF adjacency acceptance. The recurring risk here is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. The more targeted safeguard is “Check inter-area LSA propagation from each ABR after topology changes” because the preventive or detective safeguard is: Check inter-area LSA propagation from each ABR after topology changes.

B:

“Check duplicate router IDs in configuration reviews and fault diagnostics” addresses recurrence of another problem: OSPF neighbors become stuck in ExStart because both routers are configured with the same router ID. That problem depends on: The preventive or detective safeguard is: Check duplicate router IDs in configuration reviews and fault diagnostics. The recurring risk here is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. The more targeted safeguard is “Check inter-area LSA propagation from each ABR after topology changes” because the preventive or detective safeguard is: Check inter-area LSA propagation from each ABR after topology changes.

C:

“Inspect both LSDB and routing table when evaluating routing-filter controls” addresses recurrence of another problem: An engineer uses a prefix-filter on one OSPF router expecting to prevent every other router from receiving the LSA. That problem depends on: The preventive or detective safeguard is: Inspect both LSDB and routing table when evaluating routing-filter controls. The recurring risk here is: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. The more targeted safeguard is “Check inter-area LSA propagation from each ABR after topology changes” because the preventive or detective safeguard is: Check inter-area LSA propagation from each ABR after topology changes.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests