McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 28

Question 270

At fictional Harbor Media, a network engineer supporting streaming networks is reviewing IPv6 addressing and neighbor discovery during a controlled failover exercise (HCIP-H12-821-IPV6-068). The observed network issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. Which routing, switching, or network principle best explains the appropriate solution?

  1. VRRP priority and preemption behavior are separate configured failover choices.
  2. IP reachability alone does not imply that BGP TCP transport is permitted.
  3. IPv6 uses Neighbor Solicitation and Advertisement in place of ARP for address resolution.
  4. IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements.

Explanation

Correct Answer

D:

The governing principle is: IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements. In this scenario, the appropriate action is: Restore valid ICMPv6 router advertisements and inspect the host's default-router list. Valid evidence would show: Hosts learn the intended router and reach permitted IPv6 destinations.

Incorrect Answers

A:

“VRRP priority and preemption behavior are separate configured failover choices” responds to another technical or business failure: A maintenance engineer expects a higher-priority VRRP router to take back Master instantly although preemption is disabled. That source case depends on: VRRP priority and preemption behavior are separate configured failover choices. The present issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more direct action is “IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements” because IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements.

B:

“IP reachability alone does not imply that BGP TCP transport is permitted” responds to another technical or business failure: A border router can ping an eBGP peer yet session establishment fails because firewall ACL blocks TCP port 179. That source case depends on: IP reachability alone does not imply that BGP TCP transport is permitted. The present issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more direct action is “IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements” because IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements.

C:

“IPv6 uses Neighbor Solicitation and Advertisement in place of ARP for address resolution” responds to another technical or business failure: A router forwards IPv6 packets over a link but neighbor solicitation never receives a valid advertisement for the selected next hop. That source case depends on: IPv6 uses Neighbor Solicitation and Advertisement in place of ARP for address resolution. The present issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more direct action is “IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements” because IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements.

Question 271

At fictional Harbor Media, a network engineer supporting streaming networks is reviewing IPv6 addressing and neighbor discovery during a controlled failover exercise (HCIP-H12-821-IPV6-068). The observed network issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. Which ongoing preventive or detective control would best reduce recurrence?

  1. Verify neighbor roles before escalating stable 2-Way observations.
  2. Verify address, gateway and routing tables during every new IPv6 interface build.
  3. Test RA propagation and router lifetime after IPv6 VLAN changes.
  4. Inspect both LSDB and routing table when evaluating routing-filter controls.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Test RA propagation and router lifetime after IPv6 VLAN changes. This directly addresses the recurring fault: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The corrective action would be: Restore valid ICMPv6 router advertisements and inspect the host's default-router list. Success is demonstrated when: Hosts learn the intended router and reach permitted IPv6 destinations.

Incorrect Answers

A:

“Verify neighbor roles before escalating stable 2-Way observations” addresses recurrence of another problem: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. That problem depends on: The preventive or detective safeguard is: Verify neighbor roles before escalating stable 2-Way observations. The recurring risk here is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more targeted safeguard is “Test RA propagation and router lifetime after IPv6 VLAN changes” because the preventive or detective safeguard is: Test RA propagation and router lifetime after IPv6 VLAN changes.

B:

“Verify address, gateway and routing tables during every new IPv6 interface build” addresses recurrence of another problem: An engineer configures an IPv6 global unicast address but assumes this automatically establishes external default routing. That problem depends on: The preventive or detective safeguard is: Verify address, gateway and routing tables during every new IPv6 interface build. The recurring risk here is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more targeted safeguard is “Test RA propagation and router lifetime after IPv6 VLAN changes” because the preventive or detective safeguard is: Test RA propagation and router lifetime after IPv6 VLAN changes.

D:

“Inspect both LSDB and routing table when evaluating routing-filter controls” addresses recurrence of another problem: An engineer uses a prefix-filter on one OSPF router expecting to prevent every other router from receiving the LSA. That problem depends on: The preventive or detective safeguard is: Inspect both LSDB and routing table when evaluating routing-filter controls. The recurring risk here is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more targeted safeguard is “Test RA propagation and router lifetime after IPv6 VLAN changes” because the preventive or detective safeguard is: Test RA propagation and router lifetime after IPv6 VLAN changes.

Question 272

At fictional Harbor Media, a network engineer supporting streaming networks is reviewing IPv6 addressing and neighbor discovery during a controlled failover exercise (HCIP-H12-821-IPV6-068). The observed network issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. Which observation most directly verifies that the corrective change succeeded?

  1. Adjacency stays stable after underlying packet loss or timer sensitivity is corrected.
  2. Ownership returns according to documented preemption behavior without unexpected oscillation.
  3. Hosts learn the intended router and reach permitted IPv6 destinations.
  4. Test hosts reach remote prefixes through the intended ::/0 next hop.

Explanation

Correct Answer

C:

The best verification observation is: Hosts learn the intended router and reach permitted IPv6 destinations. It demonstrates the corrective action: Restore valid ICMPv6 router advertisements and inspect the host's default-router list. This fits the principle: IPv6 SLAAC and default-router discovery depend on Neighbor Discovery router advertisements. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Adjacency stays stable after underlying packet loss or timer sensitivity is corrected” responds to another technical or business failure: An OSPF neighbor oscillates between Full and Down on a congested shared segment despite correct area IDs. That source case depends on: The best verification observation is: Adjacency stays stable after underlying packet loss or timer sensitivity is corrected. The present issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more direct action is “Hosts learn the intended router and reach permitted IPv6 destinations” because the best verification observation is: Hosts learn the intended router and reach permitted IPv6 destinations.

B:

“Ownership returns according to documented preemption behavior without unexpected oscillation” responds to another technical or business failure: A maintenance engineer expects a higher-priority VRRP router to take back Master instantly although preemption is disabled. That source case depends on: The best verification observation is: Ownership returns according to documented preemption behavior without unexpected oscillation. The present issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more direct action is “Hosts learn the intended router and reach permitted IPv6 destinations” because the best verification observation is: Hosts learn the intended router and reach permitted IPv6 destinations.

D:

“Test hosts reach remote prefixes through the intended ::/0 next hop” responds to another technical or business failure: An engineer configures an IPv6 global unicast address but assumes this automatically establishes external default routing. That source case depends on: The best verification observation is: Test hosts reach remote prefixes through the intended ::/0 next hop. The present issue is: An IPv6 host cannot resolve its default gateway because router advertisements are blocked on the access VLAN. The more direct action is “Hosts learn the intended router and reach permitted IPv6 destinations” because the best verification observation is: Hosts learn the intended router and reach permitted IPv6 destinations.

Question 273

At fictional Alder Community, a network engineer supporting regional administration is reviewing VRRP, BFD and redundancy design during a supervised route change (HCIP-H12-821-RELIABILITY-069). The observed network issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. Which routing, switching, or network principle best explains the appropriate solution?

  1. Gateway availability and end-to-end network reachability are different reliability properties.
  2. BFD detection speed depends on compatible transmit and receive timers and multiplier behavior.
  3. Network reliability depends on eliminating shared risks, not only duplicating network devices.
  4. VRRP interface or route tracking can couple gateway priority to actual upstream health.

Explanation

Correct Answer

D:

The governing principle is: VRRP interface or route tracking can couple gateway priority to actual upstream health. In this scenario, the appropriate action is: Configure supported VRRP uplink tracking and suitable priority decrement. Valid evidence would show: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address.

Incorrect Answers

A:

“Gateway availability and end-to-end network reachability are different reliability properties” responds to another technical or business failure: A VRRP virtual IP responds locally but remote services fail because both gateway uplinks have lost their default route. That source case depends on: Gateway availability and end-to-end network reachability are different reliability properties. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “VRRP interface or route tracking can couple gateway priority to actual upstream health” because VRRP interface or route tracking can couple gateway priority to actual upstream health.

B:

“BFD detection speed depends on compatible transmit and receive timers and multiplier behavior” responds to another technical or business failure: BFD keeps an OSPF neighbor Down even after link restoration because the negotiated intervals or detection multiplier are incompatible. That source case depends on: BFD detection speed depends on compatible transmit and receive timers and multiplier behavior. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “VRRP interface or route tracking can couple gateway priority to actual upstream health” because VRRP interface or route tracking can couple gateway priority to actual upstream health.

C:

“Network reliability depends on eliminating shared risks, not only duplicating network devices” responds to another technical or business failure: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. That source case depends on: Network reliability depends on eliminating shared risks, not only duplicating network devices. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “VRRP interface or route tracking can couple gateway priority to actual upstream health” because VRRP interface or route tracking can couple gateway priority to actual upstream health.

Question 274

At fictional Alder Community, a network engineer supporting regional administration is reviewing VRRP, BFD and redundancy design during a supervised route change (HCIP-H12-821-RELIABILITY-069). The observed network issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. Which observation most directly verifies that the corrective change succeeded?

  1. Gateway mastership remains stable through normal transients and changes on genuine failure.
  2. Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address.
  3. Hosts resolve the intended virtual MAC and maintain service during master changes.
  4. Each router recognizes the intended group advertisements and one stable master remains.

Explanation

Correct Answer

B:

The best verification observation is: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address. It demonstrates the corrective action: Configure supported VRRP uplink tracking and suitable priority decrement. This fits the principle: VRRP interface or route tracking can couple gateway priority to actual upstream health. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Gateway mastership remains stable through normal transients and changes on genuine failure” responds to another technical or business failure: A VRRP group flaps repeatedly because upstream connectivity causes tracked priority to alternate around the peer threshold. That source case depends on: The best verification observation is: Gateway mastership remains stable through normal transients and changes on genuine failure. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address” because the best verification observation is: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address.

C:

“Hosts resolve the intended virtual MAC and maintain service during master changes” responds to another technical or business failure: Two edge routers use independent VRRP groups with conflicting virtual MAC expectations and clients intermittently lose connectivity. That source case depends on: The best verification observation is: Hosts resolve the intended virtual MAC and maintain service during master changes. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address” because the best verification observation is: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address.

D:

“Each router recognizes the intended group advertisements and one stable master remains” responds to another technical or business failure: Two VRRP routers advertise the same group but use mismatched authentication or version support settings. That source case depends on: The best verification observation is: Each router recognizes the intended group advertisements and one stable master remains. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address” because the best verification observation is: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address.

Question 275

At fictional Alder Community, a network engineer supporting regional administration is reviewing VRRP, BFD and redundancy design during a supervised route change (HCIP-H12-821-RELIABILITY-069). The observed network issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. Which ongoing preventive or detective control would best reduce recurrence?

  1. Test member and uplink loss separately in stack design validation.
  2. Measure detection and end-to-end recovery rather than relying on configured timer values.
  3. Simulate uplink failures instead of only shutting down the client-facing VLAN.
  4. Compare configured and negotiated BFD timers during network changes.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Simulate uplink failures instead of only shutting down the client-facing VLAN. This directly addresses the recurring fault: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The corrective action would be: Configure supported VRRP uplink tracking and suitable priority decrement. Success is demonstrated when: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address.

Incorrect Answers

A:

“Test member and uplink loss separately in stack design validation” addresses recurrence of another problem: A switch stack offers redundant members but its sole uplink attaches to one device and remains a failure point. That problem depends on: The preventive or detective safeguard is: Test member and uplink loss separately in stack design validation. The recurring risk here is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more targeted safeguard is “Simulate uplink failures instead of only shutting down the client-facing VLAN” because the preventive or detective safeguard is: Simulate uplink failures instead of only shutting down the client-facing VLAN.

B:

“Measure detection and end-to-end recovery rather than relying on configured timer values” addresses recurrence of another problem: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. That problem depends on: The preventive or detective safeguard is: Measure detection and end-to-end recovery rather than relying on configured timer values. The recurring risk here is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more targeted safeguard is “Simulate uplink failures instead of only shutting down the client-facing VLAN” because the preventive or detective safeguard is: Simulate uplink failures instead of only shutting down the client-facing VLAN.

D:

“Compare configured and negotiated BFD timers during network changes” addresses recurrence of another problem: BFD keeps an OSPF neighbor Down even after link restoration because the negotiated intervals or detection multiplier are incompatible. That problem depends on: The preventive or detective safeguard is: Compare configured and negotiated BFD timers during network changes. The recurring risk here is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more targeted safeguard is “Simulate uplink failures instead of only shutting down the client-facing VLAN” because the preventive or detective safeguard is: Simulate uplink failures instead of only shutting down the client-facing VLAN.

Question 276

At fictional Alder Community, a network engineer supporting regional administration is reviewing VRRP, BFD and redundancy design during a supervised route change (HCIP-H12-821-RELIABILITY-069). The observed network issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. Which next engineering action best addresses the reported problem?

  1. Adjust appropriate tracking conditions, hysteresis or delay settings and repair unstable uplink state.
  2. Verify routing protocol and FIB state separately from the BFD liveliness signal.
  3. Configure supported VRRP uplink tracking and suitable priority decrement.
  4. Repair the underlying link and choose supported detection timers or BFD that match availability requirements.

Explanation

Correct Answer

C:

The directly responsive action is: Configure supported VRRP uplink tracking and suitable priority decrement. The specific reported fault is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. Confirmation should show: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address. The supporting technical principle is: VRRP interface or route tracking can couple gateway priority to actual upstream health.

Incorrect Answers

A:

“Adjust appropriate tracking conditions, hysteresis or delay settings and repair unstable uplink state” responds to another technical or business failure: A VRRP group flaps repeatedly because upstream connectivity causes tracked priority to alternate around the peer threshold. That source case depends on: Unstable track state can cause repeated virtual-gateway ownership changes. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “Configure supported VRRP uplink tracking and suitable priority decrement” because VRRP interface or route tracking can couple gateway priority to actual upstream health.

B:

“Verify routing protocol and FIB state separately from the BFD liveliness signal” responds to another technical or business failure: A BFD session is Up but a technician assumes that means every destination route through the neighbor is installed. That source case depends on: BFD monitors a forwarding path but does not by itself create routing advertisements. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “Configure supported VRRP uplink tracking and suitable priority decrement” because VRRP interface or route tracking can couple gateway priority to actual upstream health.

D:

“Repair the underlying link and choose supported detection timers or BFD that match availability requirements” responds to another technical or business failure: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. That source case depends on: Reliability design balances false failures against convergence latency. The present issue is: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. The more direct action is “Configure supported VRRP uplink tracking and suitable priority decrement” because VRRP interface or route tracking can couple gateway priority to actual upstream health.

Question 277

At fictional Quayside Education, a network engineer supporting learning sites is reviewing IGMP and PIM multicast distribution during a planned network scaling change (HCIP-H12-821-MULTICAST-070). The observed network issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. Which routing, switching, or network principle best explains the appropriate solution?

  1. Multicast forwarding depends on current unicast or multicast RPF route calculation.
  2. Multicast state and RPF lookup follow routing-instance separation.
  3. SSM receivers identify the source and group and avoid general ASM RP discovery.
  4. IP multicast can distribute a single source flow efficiently along a receiver tree.

Explanation

Correct Answer

C:

The governing principle is: SSM receivers identify the source and group and avoid general ASM RP discovery. In this scenario, the appropriate action is: Configure compatible IGMPv3 source filters and source-specific PIM behavior. Valid evidence would show: Only the requested source-group stream is delivered without RP-based ambiguity.

Incorrect Answers

A:

“Multicast forwarding depends on current unicast or multicast RPF route calculation” responds to another technical or business failure: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. That source case depends on: Multicast forwarding depends on current unicast or multicast RPF route calculation. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “SSM receivers identify the source and group and avoid general ASM RP discovery” because SSM receivers identify the source and group and avoid general ASM RP discovery.

B:

“Multicast state and RPF lookup follow routing-instance separation” responds to another technical or business failure: A multicast over WAN deployment works within a VLAN but fails at the site boundary because the routing instance differs. That source case depends on: Multicast state and RPF lookup follow routing-instance separation. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “SSM receivers identify the source and group and avoid general ASM RP discovery” because SSM receivers identify the source and group and avoid general ASM RP discovery.

D:

“IP multicast can distribute a single source flow efficiently along a receiver tree” responds to another technical or business failure: A video stream from one sender is replicated as unicast to hundreds of recipients and saturates the WAN. That source case depends on: IP multicast can distribute a single source flow efficiently along a receiver tree. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “SSM receivers identify the source and group and avoid general ASM RP discovery” because SSM receivers identify the source and group and avoid general ASM RP discovery.

Question 278

At fictional Quayside Education, a network engineer supporting learning sites is reviewing IGMP and PIM multicast distribution during a planned network scaling change (HCIP-H12-821-MULTICAST-070). The observed network issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. Which ongoing preventive or detective control would best reduce recurrence?

  1. Validate snooping memberships after each VLAN access change.
  2. Test group join and leave handling with controlled receivers.
  3. Audit multicast outgoing-interface lists after receiver churn.
  4. Include explicit (source, group) joins in SSM acceptance tests.

Explanation

Correct Answer

D:

The preventive or detective safeguard is: Include explicit (source, group) joins in SSM acceptance tests. This directly addresses the recurring fault: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The corrective action would be: Configure compatible IGMPv3 source filters and source-specific PIM behavior. Success is demonstrated when: Only the requested source-group stream is delivered without RP-based ambiguity.

Incorrect Answers

A:

“Validate snooping memberships after each VLAN access change” addresses recurrence of another problem: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. That problem depends on: The preventive or detective safeguard is: Validate snooping memberships after each VLAN access change. The recurring risk here is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more targeted safeguard is “Include explicit (source, group) joins in SSM acceptance tests” because the preventive or detective safeguard is: Include explicit (source, group) joins in SSM acceptance tests.

B:

“Test group join and leave handling with controlled receivers” addresses recurrence of another problem: An IGMPv2 receiver leaves a group but the switch continues forwarding the stream indefinitely. That problem depends on: The preventive or detective safeguard is: Test group join and leave handling with controlled receivers. The recurring risk here is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more targeted safeguard is “Include explicit (source, group) joins in SSM acceptance tests” because the preventive or detective safeguard is: Include explicit (source, group) joins in SSM acceptance tests.

C:

“Audit multicast outgoing-interface lists after receiver churn” addresses recurrence of another problem: An upstream router continuously forwards multicast after a branch has no receivers because PIM prune information is missing. That problem depends on: The preventive or detective safeguard is: Audit multicast outgoing-interface lists after receiver churn. The recurring risk here is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more targeted safeguard is “Include explicit (source, group) joins in SSM acceptance tests” because the preventive or detective safeguard is: Include explicit (source, group) joins in SSM acceptance tests.

Question 279

At fictional Quayside Education, a network engineer supporting learning sites is reviewing IGMP and PIM multicast distribution during a planned network scaling change (HCIP-H12-821-MULTICAST-070). The observed network issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. Which next engineering action best addresses the reported problem?

  1. Evaluate multicast distribution with correct group membership and routed multicast state.
  2. Assign unique approved group ranges and check IGMP or PIM subscriptions.
  3. Configure compatible IGMPv3 source filters and source-specific PIM behavior.
  4. Enable and validate PIM on all required routed multicast hops in the distribution tree.

Explanation

Correct Answer

C:

The directly responsive action is: Configure compatible IGMPv3 source filters and source-specific PIM behavior. The specific reported fault is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. Confirmation should show: Only the requested source-group stream is delivered without RP-based ambiguity. The supporting technical principle is: SSM receivers identify the source and group and avoid general ASM RP discovery.

Incorrect Answers

A:

“Evaluate multicast distribution with correct group membership and routed multicast state” responds to another technical or business failure: A video stream from one sender is replicated as unicast to hundreds of recipients and saturates the WAN. That source case depends on: IP multicast can distribute a single source flow efficiently along a receiver tree. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “Configure compatible IGMPv3 source filters and source-specific PIM behavior” because SSM receivers identify the source and group and avoid general ASM RP discovery.

B:

“Assign unique approved group ranges and check IGMP or PIM subscriptions” responds to another technical or business failure: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. That source case depends on: Multicast group addressing must be managed as an intentional shared network namespace. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “Configure compatible IGMPv3 source filters and source-specific PIM behavior” because SSM receivers identify the source and group and avoid general ASM RP discovery.

D:

“Enable and validate PIM on all required routed multicast hops in the distribution tree” responds to another technical or business failure: A multicast receiver has IGMP state locally but the PIM upstream interface is disabled. That source case depends on: Local IGMP membership alone does not carry multicast across routed PIM boundaries. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “Configure compatible IGMPv3 source filters and source-specific PIM behavior” because SSM receivers identify the source and group and avoid general ASM RP discovery.

Question 280

At fictional Quayside Education, a network engineer supporting learning sites is reviewing IGMP and PIM multicast distribution during a planned network scaling change (HCIP-H12-821-MULTICAST-070). The observed network issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. Which observation most directly verifies that the corrective change succeeded?

  1. The correct incoming interface and expected outgoing interface list are installed end to end.
  2. Receivers build valid PIM-SM join state toward the intended rendezvous point.
  3. Only the requested source-group stream is delivered without RP-based ambiguity.
  4. Packets arrive on the expected RPF interface and are forwarded downstream.

Explanation

Correct Answer

C:

The best verification observation is: Only the requested source-group stream is delivered without RP-based ambiguity. It demonstrates the corrective action: Configure compatible IGMPv3 source filters and source-specific PIM behavior. This fits the principle: SSM receivers identify the source and group and avoid general ASM RP discovery. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“The correct incoming interface and expected outgoing interface list are installed end to end” responds to another technical or business failure: An engineer diagnoses multicast stream loss by checking only source packets and ignores outgoing interface list and receiver state. That source case depends on: The best verification observation is: The correct incoming interface and expected outgoing interface list are installed end to end. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “Only the requested source-group stream is delivered without RP-based ambiguity” because the best verification observation is: Only the requested source-group stream is delivered without RP-based ambiguity.

B:

“Receivers build valid PIM-SM join state toward the intended rendezvous point” responds to another technical or business failure: A PIM sparse-mode receiver joins a group but no rendezvous point is reachable in the intended PIM domain. That source case depends on: The best verification observation is: Receivers build valid PIM-SM join state toward the intended rendezvous point. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “Only the requested source-group stream is delivered without RP-based ambiguity” because the best verification observation is: Only the requested source-group stream is delivered without RP-based ambiguity.

D:

“Packets arrive on the expected RPF interface and are forwarded downstream” responds to another technical or business failure: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. That source case depends on: The best verification observation is: Packets arrive on the expected RPF interface and are forwarded downstream. The present issue is: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. The more direct action is “Only the requested source-group stream is delivered without RP-based ambiguity” because the best verification observation is: Only the requested source-group stream is delivered without RP-based ambiguity.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests