McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 39

Question 380

At fictional Summit Agriculture, a network engineer supporting remote rural branches is reviewing RSTP, MSTP and switching interconnects during a baseline compliance test (HCIP-H12-821-SWITCH-095). The observed network issue is: Two switches are configured for stacking but fail to form one logical unit due to incompatible member identifiers. Which next engineering action best addresses the reported problem?

  1. Check split-brain prevention mechanisms and stack topology supported by the platform.
  2. Align stack member identities, link topology and compatible software and hardware requirements.
  3. Remove inappropriate edge-port assumptions and enforce supported BPDU protection policy.
  4. Permit the intended tagged VLAN on both sides of the trunk without broadening unrelated VLAN access.

Explanation

Correct Answer

B:

The directly responsive action is: Align stack member identities, link topology and compatible software and hardware requirements. The specific reported fault is: Two switches are configured for stacking but fail to form one logical unit due to incompatible member identifiers. Confirmation should show: Both members appear in one stable logical stack with correct master and standby roles. The supporting technical principle is: Switch stacking creates a logical control relationship from compatible physical members.

Incorrect Answers

A:

“Check split-brain prevention mechanisms and stack topology supported by the platform” responds to another technical or business failure: An iStack link fails and an engineer assumes the remaining members will always preserve a single partition-free control plane. That source case depends on: Stack resiliency requires deliberate master election and partition handling. The present issue is: Two switches are configured for stacking but fail to form one logical unit due to incompatible member identifiers. The more direct action is “Align stack member identities, link topology and compatible software and hardware requirements” because Switch stacking creates a logical control relationship from compatible physical members.

C:

“Remove inappropriate edge-port assumptions and enforce supported BPDU protection policy” responds to another technical or business failure: An engineer places an edge-port setting on a trunk toward another switch and an unexpected BPDU enters the network. That source case depends on: Edge-port optimizations are intended for endpoint-facing links rather than switch-to-switch trunks. The present issue is: Two switches are configured for stacking but fail to form one logical unit due to incompatible member identifiers. The more direct action is “Align stack member identities, link topology and compatible software and hardware requirements” because Switch stacking creates a logical control relationship from compatible physical members.

D:

“Permit the intended tagged VLAN on both sides of the trunk without broadening unrelated VLAN access” responds to another technical or business failure: A technician adds a new VLAN but leaves it out of the allowed trunk list between access and aggregation switches. That source case depends on: VLAN trunking requires explicit compatible tagging and allowed membership. The present issue is: Two switches are configured for stacking but fail to form one logical unit due to incompatible member identifiers. The more direct action is “Align stack member identities, link topology and compatible software and hardware requirements” because Switch stacking creates a logical control relationship from compatible physical members.

Question 381

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing IGMP and PIM multicast distribution during a production cutover (HCIP-H12-821-MULTICAST-096). The observed network issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. Which next engineering action best addresses the reported problem?

  1. Check reverse path to the source and verify supported SPT switching behavior.
  2. Evaluate multicast distribution with correct group membership and routed multicast state.
  3. Repair downstream membership state and correct PIM prune propagation.
  4. Assign unique approved group ranges and check IGMP or PIM subscriptions.

Explanation

Correct Answer

D:

The directly responsive action is: Assign unique approved group ranges and check IGMP or PIM subscriptions. The specific reported fault is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. Confirmation should show: Only intended receivers for each service group see the correct media flow. The supporting technical principle is: Multicast group addressing must be managed as an intentional shared network namespace.

Incorrect Answers

A:

“Check reverse path to the source and verify supported SPT switching behavior” responds to another technical or business failure: A PIM-SM router cannot switch efficiently to a shortest-path tree because its source route points through another neighbor. That source case depends on: PIM-SM can transition from an RP shared tree to a source-specific shortest-path tree. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Assign unique approved group ranges and check IGMP or PIM subscriptions” because Multicast group addressing must be managed as an intentional shared network namespace.

B:

“Evaluate multicast distribution with correct group membership and routed multicast state” responds to another technical or business failure: A video stream from one sender is replicated as unicast to hundreds of recipients and saturates the WAN. That source case depends on: IP multicast can distribute a single source flow efficiently along a receiver tree. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Assign unique approved group ranges and check IGMP or PIM subscriptions” because Multicast group addressing must be managed as an intentional shared network namespace.

C:

“Repair downstream membership state and correct PIM prune propagation” responds to another technical or business failure: An upstream router continuously forwards multicast after a branch has no receivers because PIM prune information is missing. That source case depends on: PIM forwarding state should track downstream interest and prune unused paths. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Assign unique approved group ranges and check IGMP or PIM subscriptions” because Multicast group addressing must be managed as an intentional shared network namespace.

Question 382

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing IGMP and PIM multicast distribution during a production cutover (HCIP-H12-821-MULTICAST-096). The observed network issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. Which routing, switching, or network principle best explains the appropriate solution?

  1. PIM-SM can transition from an RP shared tree to a source-specific shortest-path tree.
  2. Multicast group addressing must be managed as an intentional shared network namespace.
  3. Local IGMP membership alone does not carry multicast across routed PIM boundaries.
  4. PIM-DM initially floods and prunes while PIM-SM builds receiver-oriented trees.

Explanation

Correct Answer

B:

The governing principle is: Multicast group addressing must be managed as an intentional shared network namespace. In this scenario, the appropriate action is: Assign unique approved group ranges and check IGMP or PIM subscriptions. Valid evidence would show: Only intended receivers for each service group see the correct media flow.

Incorrect Answers

A:

“PIM-SM can transition from an RP shared tree to a source-specific shortest-path tree” responds to another technical or business failure: A PIM-SM router cannot switch efficiently to a shortest-path tree because its source route points through another neighbor. That source case depends on: PIM-SM can transition from an RP shared tree to a source-specific shortest-path tree. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Multicast group addressing must be managed as an intentional shared network namespace” because Multicast group addressing must be managed as an intentional shared network namespace.

C:

“Local IGMP membership alone does not carry multicast across routed PIM boundaries” responds to another technical or business failure: A multicast receiver has IGMP state locally but the PIM upstream interface is disabled. That source case depends on: Local IGMP membership alone does not carry multicast across routed PIM boundaries. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Multicast group addressing must be managed as an intentional shared network namespace” because Multicast group addressing must be managed as an intentional shared network namespace.

D:

“PIM-DM initially floods and prunes while PIM-SM builds receiver-oriented trees” responds to another technical or business failure: A PIM dense-mode network floods large multicast volumes to branches with no interested receivers. That source case depends on: PIM-DM initially floods and prunes while PIM-SM builds receiver-oriented trees. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Multicast group addressing must be managed as an intentional shared network namespace” because Multicast group addressing must be managed as an intentional shared network namespace.

Question 383

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing IGMP and PIM multicast distribution during a production cutover (HCIP-H12-821-MULTICAST-096). The observed network issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. Which ongoing preventive or detective control would best reduce recurrence?

  1. Verify RP mappings and unicast reachability in every multicast VRF.
  2. Maintain a group-address registry for application onboarding.
  3. Check the querier role and aging timers during multicast incidents.
  4. Validate snooping memberships after each VLAN access change.

Explanation

Correct Answer

B:

The preventive or detective safeguard is: Maintain a group-address registry for application onboarding. This directly addresses the recurring fault: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The corrective action would be: Assign unique approved group ranges and check IGMP or PIM subscriptions. Success is demonstrated when: Only intended receivers for each service group see the correct media flow.

Incorrect Answers

A:

“Verify RP mappings and unicast reachability in every multicast VRF” addresses recurrence of another problem: A PIM sparse-mode receiver joins a group but no rendezvous point is reachable in the intended PIM domain. That problem depends on: The preventive or detective safeguard is: Verify RP mappings and unicast reachability in every multicast VRF. The recurring risk here is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more targeted safeguard is “Maintain a group-address registry for application onboarding” because the preventive or detective safeguard is: Maintain a group-address registry for application onboarding.

C:

“Check the querier role and aging timers during multicast incidents” addresses recurrence of another problem: A multicast router sees no group receivers because IGMP query messages are absent from a VLAN. That problem depends on: The preventive or detective safeguard is: Check the querier role and aging timers during multicast incidents. The recurring risk here is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more targeted safeguard is “Maintain a group-address registry for application onboarding” because the preventive or detective safeguard is: Maintain a group-address registry for application onboarding.

D:

“Validate snooping memberships after each VLAN access change” addresses recurrence of another problem: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. That problem depends on: The preventive or detective safeguard is: Validate snooping memberships after each VLAN access change. The recurring risk here is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more targeted safeguard is “Maintain a group-address registry for application onboarding” because the preventive or detective safeguard is: Maintain a group-address registry for application onboarding.

Question 384

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing IGMP and PIM multicast distribution during a production cutover (HCIP-H12-821-MULTICAST-096). The observed network issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. Which observation most directly verifies that the corrective change succeeded?

  1. Only intended receivers for each service group see the correct media flow.
  2. Only intended receiver branches obtain a shared group stream with reduced duplicate transmission.
  3. Only the requested source-group stream is delivered without RP-based ambiguity.
  4. Multicast packets resume on the revised valid RPF interface after failover.

Explanation

Correct Answer

A:

The best verification observation is: Only intended receivers for each service group see the correct media flow. It demonstrates the corrective action: Assign unique approved group ranges and check IGMP or PIM subscriptions. This fits the principle: Multicast group addressing must be managed as an intentional shared network namespace. Verify on the actual Huawei platform and network release.

Incorrect Answers

B:

“Only intended receiver branches obtain a shared group stream with reduced duplicate transmission” responds to another technical or business failure: A video stream from one sender is replicated as unicast to hundreds of recipients and saturates the WAN. That source case depends on: The best verification observation is: Only intended receiver branches obtain a shared group stream with reduced duplicate transmission. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Only intended receivers for each service group see the correct media flow” because the best verification observation is: Only intended receivers for each service group see the correct media flow.

C:

“Only the requested source-group stream is delivered without RP-based ambiguity” responds to another technical or business failure: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. That source case depends on: The best verification observation is: Only the requested source-group stream is delivered without RP-based ambiguity. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Only intended receivers for each service group see the correct media flow” because the best verification observation is: Only intended receivers for each service group see the correct media flow.

D:

“Multicast packets resume on the revised valid RPF interface after failover” responds to another technical or business failure: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. That source case depends on: The best verification observation is: Multicast packets resume on the revised valid RPF interface after failover. The present issue is: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. The more direct action is “Only intended receivers for each service group see the correct media flow” because the best verification observation is: Only intended receivers for each service group see the correct media flow.

Question 385

At fictional Dovetail University, a network engineer supporting campus routing is reviewing route-policy and traffic-control behavior during a customer network audit (HCIP-H12-821-POLICY-097). The observed network issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. Which routing, switching, or network principle best explains the appropriate solution?

  1. Route redistribution crosses protocol boundaries and needs controlled prefix filtering.
  2. Egress congestion scheduling determines queuing delay among traffic classes.
  3. Route attribute creation alone does not guarantee propagation across a BGP session.
  4. Routing protocol preference is broad selection behavior unless narrowed by policy.

Explanation

Correct Answer

D:

The governing principle is: Routing protocol preference is broad selection behavior unless narrowed by policy. In this scenario, the appropriate action is: Select targeted route matching rather than blanket changes to the routing protocol preference. Valid evidence would show: The intended service flow changes next hop while other routes retain established egress.

Incorrect Answers

A:

“Route redistribution crosses protocol boundaries and needs controlled prefix filtering” responds to another technical or business failure: A site redistributes static routes into OSPF and accidentally advertises a management-only address to every area. That source case depends on: Route redistribution crosses protocol boundaries and needs controlled prefix filtering. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “Routing protocol preference is broad selection behavior unless narrowed by policy” because Routing protocol preference is broad selection behavior unless narrowed by policy.

B:

“Egress congestion scheduling determines queuing delay among traffic classes” responds to another technical or business failure: A campus egress port uses weighted scheduling but latency-sensitive voice sits behind large bulk transfers. That source case depends on: Egress congestion scheduling determines queuing delay among traffic classes. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “Routing protocol preference is broad selection behavior unless narrowed by policy” because Routing protocol preference is broad selection behavior unless narrowed by policy.

C:

“Route attribute creation alone does not guarantee propagation across a BGP session” responds to another technical or business failure: An outbound route-policy appends a community but the upstream device removes communities when send behavior is disabled. That source case depends on: Route attribute creation alone does not guarantee propagation across a BGP session. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “Routing protocol preference is broad selection behavior unless narrowed by policy” because Routing protocol preference is broad selection behavior unless narrowed by policy.

Question 386

At fictional Dovetail University, a network engineer supporting campus routing is reviewing route-policy and traffic-control behavior during a customer network audit (HCIP-H12-821-POLICY-097). The observed network issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. Which observation most directly verifies that the corrective change succeeded?

  1. Packets retain intended service classification through each trusted hop.
  2. Upstream observed updates carry permitted communities and service-specific actions occur.
  3. OSPF external LSAs exclude the management subnet and include permitted service destinations.
  4. The intended service flow changes next hop while other routes retain established egress.

Explanation

Correct Answer

D:

The best verification observation is: The intended service flow changes next hop while other routes retain established egress. It demonstrates the corrective action: Select targeted route matching rather than blanket changes to the routing protocol preference. This fits the principle: Routing protocol preference is broad selection behavior unless narrowed by policy. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Packets retain intended service classification through each trusted hop” responds to another technical or business failure: A QoS policy marks packets DSCP but a downstream switch strips or overwrites those markings. That source case depends on: The best verification observation is: Packets retain intended service classification through each trusted hop. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “The intended service flow changes next hop while other routes retain established egress” because the best verification observation is: The intended service flow changes next hop while other routes retain established egress.

B:

“Upstream observed updates carry permitted communities and service-specific actions occur” responds to another technical or business failure: An outbound route-policy appends a community but the upstream device removes communities when send behavior is disabled. That source case depends on: The best verification observation is: Upstream observed updates carry permitted communities and service-specific actions occur. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “The intended service flow changes next hop while other routes retain established egress” because the best verification observation is: The intended service flow changes next hop while other routes retain established egress.

C:

“OSPF external LSAs exclude the management subnet and include permitted service destinations” responds to another technical or business failure: A site redistributes static routes into OSPF and accidentally advertises a management-only address to every area. That source case depends on: The best verification observation is: OSPF external LSAs exclude the management subnet and include permitted service destinations. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “The intended service flow changes next hop while other routes retain established egress” because the best verification observation is: The intended service flow changes next hop while other routes retain established egress.

Question 387

At fictional Dovetail University, a network engineer supporting campus routing is reviewing route-policy and traffic-control behavior during a customer network audit (HCIP-H12-821-POLICY-097). The observed network issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. Which next engineering action best addresses the reported problem?

  1. Correct the prefix-filter network and mask length parameters for intended component routes.
  2. Verify community attachment, propagation and explicit community matching at the export policy.
  3. Narrow route-policy scope to the intended neighbor, protocol and prefix sets.
  4. Select targeted route matching rather than blanket changes to the routing protocol preference.

Explanation

Correct Answer

D:

The directly responsive action is: Select targeted route matching rather than blanket changes to the routing protocol preference. The specific reported fault is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. Confirmation should show: The intended service flow changes next hop while other routes retain established egress. The supporting technical principle is: Routing protocol preference is broad selection behavior unless narrowed by policy.

Incorrect Answers

A:

“Correct the prefix-filter network and mask length parameters for intended component routes” responds to another technical or business failure: A prefix-list denies an entire /16 because its mask range does not include the intended /24 subnet entries. That source case depends on: IP prefix filtering depends on both address prefix and permitted length ranges. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “Select targeted route matching rather than blanket changes to the routing protocol preference” because Routing protocol preference is broad selection behavior unless narrowed by policy.

B:

“Verify community attachment, propagation and explicit community matching at the export policy” responds to another technical or business failure: An engineer sets a BGP route community but forgets the matching export policy and upstream advertisements are unchanged. That source case depends on: Community marking and route-policy enforcement are separate configured stages. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “Select targeted route matching rather than blanket changes to the routing protocol preference” because Routing protocol preference is broad selection behavior unless narrowed by policy.

C:

“Narrow route-policy scope to the intended neighbor, protocol and prefix sets” responds to another technical or business failure: An import routing policy changes route preference globally when only one partner's redistributed routes should be affected. That source case depends on: Policy association points control which imported routing information is modified. The present issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more direct action is “Select targeted route matching rather than blanket changes to the routing protocol preference” because Routing protocol preference is broad selection behavior unless narrowed by policy.

Question 388

At fictional Dovetail University, a network engineer supporting campus routing is reviewing route-policy and traffic-control behavior during a customer network audit (HCIP-H12-821-POLICY-097). The observed network issue is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. Which ongoing preventive or detective control would best reduce recurrence?

  1. Inventory import-policy attachment to each neighbor and protocol before deployment.
  2. Load-test all QoS queues and starvation behavior before enabling strict priority.
  3. Compare affected prefixes and VRF scope before changing route preference.
  4. Include community advertisement inspection in BGP peering acceptance.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Compare affected prefixes and VRF scope before changing route preference. This directly addresses the recurring fault: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The corrective action would be: Select targeted route matching rather than blanket changes to the routing protocol preference. Success is demonstrated when: The intended service flow changes next hop while other routes retain established egress.

Incorrect Answers

A:

“Inventory import-policy attachment to each neighbor and protocol before deployment” addresses recurrence of another problem: An import routing policy changes route preference globally when only one partner's redistributed routes should be affected. That problem depends on: The preventive or detective safeguard is: Inventory import-policy attachment to each neighbor and protocol before deployment. The recurring risk here is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more targeted safeguard is “Compare affected prefixes and VRF scope before changing route preference” because the preventive or detective safeguard is: Compare affected prefixes and VRF scope before changing route preference.

B:

“Load-test all QoS queues and starvation behavior before enabling strict priority” addresses recurrence of another problem: A campus egress port uses weighted scheduling but latency-sensitive voice sits behind large bulk transfers. That problem depends on: The preventive or detective safeguard is: Load-test all QoS queues and starvation behavior before enabling strict priority. The recurring risk here is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more targeted safeguard is “Compare affected prefixes and VRF scope before changing route preference” because the preventive or detective safeguard is: Compare affected prefixes and VRF scope before changing route preference.

D:

“Include community advertisement inspection in BGP peering acceptance” addresses recurrence of another problem: An outbound route-policy appends a community but the upstream device removes communities when send behavior is disabled. That problem depends on: The preventive or detective safeguard is: Include community advertisement inspection in BGP peering acceptance. The recurring risk here is: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. The more targeted safeguard is “Compare affected prefixes and VRF scope before changing route preference” because the preventive or detective safeguard is: Compare affected prefixes and VRF scope before changing route preference.

Question 389

At fictional Timberline Operations, a network engineer supporting production campuses is reviewing OSPF area design and link-state convergence during a controlled failover exercise (HCIP-H12-821-OSPF-098). The observed network issue is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. Which observation most directly verifies that the corrective change succeeded?

  1. The intended interface participates in OSPF and its prefix is announced appropriately.
  2. The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR.
  3. Router IDs are unique across the domain and database exchange proceeds to Full.
  4. Database description exchange completes without fragmentation-related adjacency flaps.

Explanation

Correct Answer

A:

The best verification observation is: The intended interface participates in OSPF and its prefix is announced appropriately. It demonstrates the corrective action: Compare interface IP addresses with enabled OSPF network ranges and area bindings. This fits the principle: OSPF process activation on interfaces depends on matching enabled prefixes and area configuration. Verify on the actual Huawei platform and network release.

Incorrect Answers

B:

“The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR” responds to another technical or business failure: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. That source case depends on: The best verification observation is: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR. The present issue is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. The more direct action is “The intended interface participates in OSPF and its prefix is announced appropriately” because the best verification observation is: The intended interface participates in OSPF and its prefix is announced appropriately.

C:

“Router IDs are unique across the domain and database exchange proceeds to Full” responds to another technical or business failure: OSPF neighbors become stuck in ExStart because both routers are configured with the same router ID. That source case depends on: The best verification observation is: Router IDs are unique across the domain and database exchange proceeds to Full. The present issue is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. The more direct action is “The intended interface participates in OSPF and its prefix is announced appropriately” because the best verification observation is: The intended interface participates in OSPF and its prefix is announced appropriately.

D:

“Database description exchange completes without fragmentation-related adjacency flaps” responds to another technical or business failure: An OSPF neighbor stays in Exchange and large database description packets fail over a reduced-MTU tunnel. That source case depends on: The best verification observation is: Database description exchange completes without fragmentation-related adjacency flaps. The present issue is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. The more direct action is “The intended interface participates in OSPF and its prefix is announced appropriately” because the best verification observation is: The intended interface participates in OSPF and its prefix is announced appropriately.

Question 390

At fictional Timberline Operations, a network engineer supporting production campuses is reviewing OSPF area design and link-state convergence during a controlled failover exercise (HCIP-H12-821-OSPF-098). The observed network issue is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. Which ongoing preventive or detective control would best reduce recurrence?

  1. Validate current DR or BDR role rather than predicting it from priority alone.
  2. Document interface network types and verify after link-layer changes.
  3. Include interface participation checks in subnet migration procedures.
  4. Test cost changes with an explicit before-and-after route and path table.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Include interface participation checks in subnet migration procedures. This directly addresses the recurring fault: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. The corrective action would be: Compare interface IP addresses with enabled OSPF network ranges and area bindings. Success is demonstrated when: The intended interface participates in OSPF and its prefix is announced appropriately.

Incorrect Answers

A:

“Validate current DR or BDR role rather than predicting it from priority alone” addresses recurrence of another problem: An OSPF DR election change unexpectedly disrupts traffic because an engineer assumes elections are always preemptive. That problem depends on: The preventive or detective safeguard is: Validate current DR or BDR role rather than predicting it from priority alone. The recurring risk here is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. The more targeted safeguard is “Include interface participation checks in subnet migration procedures” because the preventive or detective safeguard is: Include interface participation checks in subnet migration procedures.

B:

“Document interface network types and verify after link-layer changes” addresses recurrence of another problem: Two OSPF devices on a point-to-point fiber cannot build an adjacency because their interface network types differ. That problem depends on: The preventive or detective safeguard is: Document interface network types and verify after link-layer changes. The recurring risk here is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. The more targeted safeguard is “Include interface participation checks in subnet migration procedures” because the preventive or detective safeguard is: Include interface participation checks in subnet migration procedures.

D:

“Test cost changes with an explicit before-and-after route and path table” addresses recurrence of another problem: An operator raises OSPF interface cost expecting every transit path to become more attractive. That problem depends on: The preventive or detective safeguard is: Test cost changes with an explicit before-and-after route and path table. The recurring risk here is: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. The more targeted safeguard is “Include interface participation checks in subnet migration procedures” because the preventive or detective safeguard is: Include interface participation checks in subnet migration procedures.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests