McAfee Secure

Exam Code: JN0-481

Exam Name: Data Center, Specialist (JNCIS-DC)

Certification Provider: Juniper

Juniper JN0-481 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

65 Questions & Answers with Testing Engine

"Data Center, Specialist (JNCIS-DC) Exam", also known as JN0-481 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-481 Exam Engine. Your JN0-481 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-481 Practice Test 6

Question 50

A spine-link migration changes a transit interface address and unexpectedly disrupts VXLAN reachability because the design never used a stable VTEP identity. Once the issue is resolved, which ongoing practice BEST prevents this type of failure?

  1. Include route type and tenant VRF checks in intersubnet rollout procedures.
  2. Document loopback allocation and verify its route advertisement during device replacement and uplink maintenance.
  3. Include encapsulation/decapsulation and VNI validation in packet-level overlay fault isolation.
  4. Include endpoint move tests and MAC route convergence monitoring during host virtualization migrations.

Explanation

Correct Answer

B:

The preventive practice is aligned with the diagnosed mechanism, not an unrelated protection. Document loopback allocation and verify its route advertisement during device replacement and uplink maintenance. Logical tunnel endpoint identity should be separated from individual physical transport paths.

Incorrect Answers

A:

EVPN Type 5 routes can carry IP prefix reachability for routed overlays independently of individual MAC/IP Type 2 host advertisements. For the current prevention question, the evidence instead states: A spine-link migration changes a transit interface address and unexpectedly disrupts VXLAN reachability because the design never used a stable VTEP identity. Here, a VTEP endpoint requires an appropriate stable IP identity reachable in the underlay, commonly on a loopback interface.

C:

VXLAN tunnel endpoints encapsulate tenant frames at ingress and decapsulate at egress using the overlay VNI context. However, the present prevention decision is grounded in: A spine-link migration changes a transit interface address and unexpectedly disrupts VXLAN reachability because the design never used a stable VTEP identity. For this issue, confirm the intended VTEP source address and advertise its loopback through the underlay so transport changes do not silently change endpoint identity.

D:

Include endpoint move tests and MAC route convergence monitoring during host virtualization migrations. Here, a VTEP endpoint requires an appropriate stable IP identity reachable in the underlay, commonly on a loopback interface.

Question 51

Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU. Which explanation BEST identifies the Juniper data-center or Apstra mechanism causing this result?

  1. A distributed anycast gateway design requires a consistent logical gateway identity across participating VTEPs for the same tenant segment.
  2. EVPN Type 3 IMET signaling can advertise VTEP membership information used for broadcast, unknown-unicast and multicast replication in a VXLAN domain.
  3. EVPN Type 2 routes distribute learned MAC and optionally IP reachability so remote VTEPs can locate a host.
  4. VXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

Explanation

Correct Answer

D:

The decisive cause is vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

Incorrect Answers

A:

A distributed anycast gateway design requires a consistent logical gateway identity across participating VTEPs for the same tenant segment. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

B:

EVPN Type 3 IMET signaling can advertise VTEP membership information used for broadcast, unknown-unicast and multicast replication in a VXLAN domain. That concerns EVPN Type 3 inclusive membership for BUM, while the issue here is underlay MTU for VXLAN encapsulation. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

C:

EVPN Type 2 routes distribute learned MAC and optionally IP reachability so remote VTEPs can locate a host. For this issue, measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

Question 52

Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU. Which configuration or operational action MOST directly addresses the problem?

  1. Trace VTEP source/destination, outer transport and VNI at ingress and egress, then align the receiving bridge-domain attachment.
  2. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.
  3. Correlate interface errors, supported BFD or routing-neighbor state and route withdrawal, then correct the underlay fault and validate recovery.
  4. Restore and verify the underlay route to the remote VTEP loopback and its next hops before troubleshooting tenant bridging again.

Explanation

Correct Answer

B:

In this case, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.

Incorrect Answers

A:

VXLAN tunnel endpoints encapsulate tenant frames at ingress and decapsulate at egress using the overlay VNI context. However, the present correction decision is grounded in: Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU. For this issue, measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

C:

Correlate interface errors, supported BFD or routing-neighbor state and route withdrawal, then correct the underlay fault and validate recovery. That concerns underlay failure isolation using BFD and route state rather than underlay MTU for VXLAN encapsulation. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.

D:

Overlay reachability depends on the IP underlay being able to route packets between the VTEP endpoints advertised by the control plane. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

Question 53

Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU. The team proposes: Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design. Which data-center or operational principle BEST justifies that choice?

  1. Tunnel reachability for small packets does not prove the transport supports full-size encapsulated application traffic.
  2. Two physical links alone do not create a coordinated EVPN Ethernet segment.
  3. The routed fabric foundation depends on working protocol adjacencies and installed prefixes, not merely Ethernet carrier.
  4. Logical tunnel endpoint identity should be separated from individual physical transport paths.

Explanation

Correct Answer

A:

Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU. The central principle is tunnel reachability for small packets does not prove the transport supports full-size encapsulated application traffic. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

Incorrect Answers

B:

Two physical links alone do not create a coordinated EVPN Ethernet segment. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

C:

The routed fabric foundation depends on working protocol adjacencies and installed prefixes, not merely Ethernet carrier. That concerns BGP underlay adjacency versus established overlay rather than underlay MTU for VXLAN encapsulation. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.

D:

A VTEP endpoint requires an appropriate stable IP identity reachable in the underlay, commonly on a loopback interface. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

Question 54

Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU. After applying this change—Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.—which observation BEST demonstrates success?

  1. The receiving VRF learns the intended IP prefix by EVPN and forwards authorized routed test traffic to the correct overlay next hop.
  2. A controlled ARP or broadcast discovery test reaches only the intended participating VTEPs while known unicast remains functional.
  3. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.
  4. The controlled frame reaches legitimate remote segments without returning to its originating shared attachment.

Explanation

Correct Answer

C:

A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops. That tests the recommended change (Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.) against the original case: Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU.

Incorrect Answers

A:

The receiving VRF learns the intended IP prefix by EVPN and forwards authorized routed test traffic to the correct overlay next hop. That concerns EVPN Type 5 routed prefix reachability, while the issue here is underlay MTU for VXLAN encapsulation. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

B:

EVPN Type 3 IMET signaling can advertise VTEP membership information used for broadcast, unknown-unicast and multicast replication in a VXLAN domain. For this issue, measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

D:

The controlled frame reaches legitimate remote segments without returning to its originating shared attachment. That concerns EVPN multihoming split-horizon behavior rather than underlay MTU for VXLAN encapsulation. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.

Question 55

Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU. Once the issue is resolved, which ongoing practice BEST prevents this type of failure?

  1. Test both positive and negative route-target import outcomes during tenant deployment.
  2. Validate distributed gateway placement and VRF association when adding VNIs or leafs.
  3. Check anycast gateway consistency whenever a tenant virtual network is extended to another rack.
  4. Include encapsulated MTU and every ECMP path in fabric acceptance and upgrade testing.

Explanation

Correct Answer

D:

A lasting control should detect the original error before release. Include encapsulated MTU and every ECMP path in fabric acceptance and upgrade testing. That is important in this case because vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload. The scenario was: Host ping tests with small payloads work across the fabric, but larger VXLAN-encapsulated application packets are dropped by an underlay interface with an insufficient MTU.

Incorrect Answers

A:

Route targets mark EVPN VPN route membership and VRF import/export decisions; an established BGP session alone does not authorize all tenant routes. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

B:

Validate distributed gateway placement and VRF association when adding VNIs or leafs. That concerns edge-routed bridging for local gateway, while the issue here is underlay MTU for VXLAN encapsulation. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

C:

A distributed anycast gateway design requires a consistent logical gateway identity across participating VTEPs for the same tenant segment. For this issue, measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

Question 56

A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. Which explanation BEST identifies the Juniper data-center or Apstra mechanism causing this result?

  1. Physical link state does not guarantee underlay routes if the intended BGP neighbors or address-family configuration fail.
  2. VXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.
  3. A VTEP endpoint requires an appropriate stable IP identity reachable in the underlay, commonly on a loopback interface.
  4. A shared Ethernet segment identity is important for supported EVPN multihoming coordination of the same access segment.

Explanation

Correct Answer

B:

The fault is not established by a generic firewall symptom alone. VXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

Incorrect Answers

A:

Physical link state does not guarantee underlay routes if the intended BGP neighbors or address-family configuration fail. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

C:

A VTEP endpoint requires an appropriate stable IP identity reachable in the underlay, commonly on a loopback interface. For this issue, measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

D:

A shared Ethernet segment identity is important for supported EVPN multihoming coordination of the same access segment. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

Question 57

A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. Which configuration or operational action MOST directly addresses the problem?

  1. Verify the supported ESI split-horizon and multihoming forwarding state, and correct mismatched peer membership before adding broader flood permissions.
  2. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.
  3. Confirm the appropriate tenant VRF and supported IP-prefix export, import targets and remote route installation before testing intersubnet traffic.
  4. Inspect the tenant's EVPN Type 3 reachability and import scope, and repair the supported BUM replication membership for its VNI.

Explanation

Correct Answer

B:

This action directly fixes the documented constraint: VXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload. Apply it to the reported case: A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. Then verify: A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.

Incorrect Answers

A:

EVPN multihoming uses loop-prevention procedures to avoid forwarding eligible frames back into the Ethernet segment from which they originated. However, the present correction decision is grounded in: A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. For this issue, measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

C:

Confirm the appropriate tenant VRF and supported IP-prefix export, import targets and remote route installation before testing intersubnet traffic. That concerns EVPN Type 5 routed prefix reachability rather than underlay MTU for VXLAN encapsulation. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.

D:

EVPN Type 3 IMET signaling can advertise VTEP membership information used for broadcast, unknown-unicast and multicast replication in a VXLAN domain. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

Question 58

A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. The team proposes: Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design. Which data-center or operational principle BEST justifies that choice?

  1. Tunnel reachability for small packets does not prove the transport supports full-size encapsulated application traffic.
  2. Logical tenant separation relies on explicit control-plane route distribution scope, not only shared fabric transport.
  3. A fabric can route at its edges instead of requiring every tenant packet to hairpin through an unrelated centralized device.
  4. Consistent distributed gateway identity helps preserve endpoint expectations when their physical attachment location changes.

Explanation

Correct Answer

A:

This principle links classification and policy semantics to the relevant failure. Tunnel reachability for small packets does not prove the transport supports full-size encapsulated application traffic. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload. The remedy under discussion is: Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

Incorrect Answers

B:

Logical tenant separation relies on explicit control-plane route distribution scope, not only shared fabric transport. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

C:

A fabric can route at its edges instead of requiring every tenant packet to hairpin through an unrelated centralized device. That concerns edge-routed bridging for local gateway rather than underlay MTU for VXLAN encapsulation. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.

D:

A distributed anycast gateway design requires a consistent logical gateway identity across participating VTEPs for the same tenant segment. For the current principle question, the evidence instead states: A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

Question 59

A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. After applying this change—Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.—which observation BEST demonstrates success?

  1. The two authorized leafs advertise coherent membership for the same segment and a controlled member-link loss follows the supported recovery behavior.
  2. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops.
  3. A bounded broadcast test arrives at the shared attachment once per intended frame and DF status matches the effective forwarding role.
  4. Failed next hops are withdrawn within the design target and authorized VXLAN traffic converges onto surviving underlay paths.

Explanation

Correct Answer

B:

The criterion directly exercises the affected flow or security object: A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops. The original condition was: A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. The relevant correction is: Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

Incorrect Answers

A:

The two authorized leafs advertise coherent membership for the same segment and a controlled member-link loss follows the supported recovery behavior. That concerns ethernet segment identifier for multihomed access, while the issue here is underlay MTU for VXLAN encapsulation. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

C:

A bounded broadcast test arrives at the shared attachment once per intended frame and DF status matches the effective forwarding role. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

D:

Failed next hops are withdrawn within the design target and authorized VXLAN traffic converges onto surviving underlay paths. That concerns underlay failure isolation using BFD and route state rather than underlay MTU for VXLAN encapsulation. A representative maximum-size tenant transfer succeeds over each selected spine path without underlay oversize drops. Specifically for the verification question, the case to validate is: A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently.

Question 60

A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. Once the issue is resolved, which ongoing practice BEST prevents this type of failure?

  1. Include encapsulated MTU and every ECMP path in fabric acceptance and upgrade testing.
  2. Document loopback allocation and verify its route advertisement during device replacement and uplink maintenance.
  3. Check interface state, BGP session state and learned prefix coverage as separate fabric health criteria.
  4. Include route type and tenant VRF checks in intersubnet rollout procedures.

Explanation

Correct Answer

A:

This control reduces recurrence of the same class of failure: VXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload. Apply the recurring practice: Include encapsulated MTU and every ECMP path in fabric acceptance and upgrade testing. The previous example was: A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently.

Incorrect Answers

B:

Document loopback allocation and verify its route advertisement during device replacement and uplink maintenance. That concerns VTEP loopback source identity stability, while the issue here is underlay MTU for VXLAN encapsulation. Measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

C:

Physical link state does not guarantee underlay routes if the intended BGP neighbors or address-family configuration fail. However, the present prevention decision is grounded in: A new spine switch uses an ordinary Ethernet MTU while adjacent leaf paths assume extra VXLAN header overhead, so large tenant frames fail intermittently. For this issue, measure encapsulation overhead and configure a consistent supported underlay MTU, or constrain overlay payload sizes according to the design.

D:

Include route type and tenant VRF checks in intersubnet rollout procedures. Here, vXLAN adds outer transport headers, making the required underlay packet size greater than the original tenant Ethernet payload.

Data Center, Specialist (JNCIS-DC) (JN0-481) Practice Tests