McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 36

Question 350

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing IS-IS level-aware topology and database synchronization during an initial deployment test (HCIP-H12-821-ISIS-088). The observed network issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. Which next engineering action best addresses the reported problem?

  1. Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability.
  2. Verify wide-metric support and configuration consistency across participating routers.
  3. Permit the appropriate IS-IS link-layer PDUs and check physical segment connectivity.
  4. Configure matching supported IS-IS Hello or LSP authentication parameters for the peering scope.

Explanation

Correct Answer

A:

The directly responsive action is: Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability. The specific reported fault is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. Confirmation should show: Other routers avoid the maintenance node for ordinary transit paths when alternatives exist. The supporting technical principle is: IS-IS overload signaling can discourage use of a router as a transit node.

Incorrect Answers

B:

“Verify wide-metric support and configuration consistency across participating routers” responds to another technical or business failure: A large IS-IS deployment uses narrow metrics until a new path cost exceeds the legacy representable range. That source case depends on: IS-IS wide metrics extend usable cost representation for modern network designs. The present issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more direct action is “Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability” because IS-IS overload signaling can discourage use of a router as a transit node.

C:

“Permit the appropriate IS-IS link-layer PDUs and check physical segment connectivity” responds to another technical or business failure: IS-IS adjacency remains Down when Hello frames are filtered by an intermediate layer-2 device. That source case depends on: IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport. The present issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more direct action is “Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability” because IS-IS overload signaling can discourage use of a router as a transit node.

D:

“Configure matching supported IS-IS Hello or LSP authentication parameters for the peering scope” responds to another technical or business failure: An IS-IS adjacency repeatedly resets because neighboring devices use incompatible authentication settings. That source case depends on: IS-IS routing integrity can require compatible authentication at the relevant PDU scope. The present issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more direct action is “Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability” because IS-IS overload signaling can discourage use of a router as a transit node.

Question 351

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing IS-IS level-aware topology and database synchronization during an initial deployment test (HCIP-H12-821-ISIS-088). The observed network issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. Which observation most directly verifies that the corrective change succeeded?

  1. The Level 1 device installs a valid route toward its local Level 1/2 router.
  2. Other routers avoid the maintenance node for ordinary transit paths when alternatives exist.
  3. Link-state packets carry supported larger metrics and computed paths match design.
  4. Only the intended reachable interarea prefixes appear in the Level 1 database.

Explanation

Correct Answer

B:

The best verification observation is: Other routers avoid the maintenance node for ordinary transit paths when alternatives exist. It demonstrates the corrective action: Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability. This fits the principle: IS-IS overload signaling can discourage use of a router as a transit node. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“The Level 1 device installs a valid route toward its local Level 1/2 router” responds to another technical or business failure: A Level 1-only router cannot reach an IP prefix advertised only outside its local IS-IS area. That source case depends on: The best verification observation is: The Level 1 device installs a valid route toward its local Level 1/2 router. The present issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more direct action is “Other routers avoid the maintenance node for ordinary transit paths when alternatives exist” because the best verification observation is: Other routers avoid the maintenance node for ordinary transit paths when alternatives exist.

C:

“Link-state packets carry supported larger metrics and computed paths match design” responds to another technical or business failure: A large IS-IS deployment uses narrow metrics until a new path cost exceeds the legacy representable range. That source case depends on: The best verification observation is: Link-state packets carry supported larger metrics and computed paths match design. The present issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more direct action is “Other routers avoid the maintenance node for ordinary transit paths when alternatives exist” because the best verification observation is: Other routers avoid the maintenance node for ordinary transit paths when alternatives exist.

D:

“Only the intended reachable interarea prefixes appear in the Level 1 database” responds to another technical or business failure: An engineer leaks all Level 2 routes into Level 1 and overwhelms a branch routing table. That source case depends on: The best verification observation is: Only the intended reachable interarea prefixes appear in the Level 1 database. The present issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more direct action is “Other routers avoid the maintenance node for ordinary transit paths when alternatives exist” because the best verification observation is: Other routers avoid the maintenance node for ordinary transit paths when alternatives exist.

Question 352

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing IS-IS level-aware topology and database synchronization during an initial deployment test (HCIP-H12-821-ISIS-088). The observed network issue is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. Which ongoing preventive or detective control would best reduce recurrence?

  1. Validate alternate reachability before setting maintenance overload state.
  2. Validate system IDs across a network before enabling IS-IS.
  3. Review leaked-prefix counts during Level 1 and Level 2 changes.
  4. Compare circuit-type values during core link acceptance.

Explanation

Correct Answer

A:

The preventive or detective safeguard is: Validate alternate reachability before setting maintenance overload state. This directly addresses the recurring fault: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The corrective action would be: Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability. Success is demonstrated when: Other routers avoid the maintenance node for ordinary transit paths when alternatives exist.

Incorrect Answers

B:

“Validate system IDs across a network before enabling IS-IS” addresses recurrence of another problem: An IS-IS configuration reuses one system ID on two distinct routers and link-state advertisements become ambiguous. That problem depends on: The preventive or detective safeguard is: Validate system IDs across a network before enabling IS-IS. The recurring risk here is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more targeted safeguard is “Validate alternate reachability before setting maintenance overload state” because the preventive or detective safeguard is: Validate alternate reachability before setting maintenance overload state.

C:

“Review leaked-prefix counts during Level 1 and Level 2 changes” addresses recurrence of another problem: An engineer leaks all Level 2 routes into Level 1 and overwhelms a branch routing table. That problem depends on: The preventive or detective safeguard is: Review leaked-prefix counts during Level 1 and Level 2 changes. The recurring risk here is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more targeted safeguard is “Validate alternate reachability before setting maintenance overload state” because the preventive or detective safeguard is: Validate alternate reachability before setting maintenance overload state.

D:

“Compare circuit-type values during core link acceptance” addresses recurrence of another problem: Two Level 2 IS-IS routers do not form neighbors because one interface is configured for Level 1-only adjacencies. That problem depends on: The preventive or detective safeguard is: Compare circuit-type values during core link acceptance. The recurring risk here is: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. The more targeted safeguard is “Validate alternate reachability before setting maintenance overload state” because the preventive or detective safeguard is: Validate alternate reachability before setting maintenance overload state.

Question 353

At fictional Timberline Operations, a network engineer supporting production campuses is reviewing route-policy and traffic-control behavior during a controlled failover exercise (HCIP-H12-821-POLICY-089). The observed network issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. Which routing, switching, or network principle best explains the appropriate solution?

  1. Routing protocol preference is broad selection behavior unless narrowed by policy.
  2. ACL enforcement is sensitive to attachment location and traffic direction.
  3. Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.
  4. Policy association points control which imported routing information is modified.

Explanation

Correct Answer

C:

The governing principle is: Policy routing can override ordinary destination lookup but still requires valid forwarding resolution. In this scenario, the appropriate action is: Correct next-hop reachability and routing-instance association before retaining the policy. Valid evidence would show: PBR-selected test packets follow a reachable authorized next hop without black holes.

Incorrect Answers

A:

“Routing protocol preference is broad selection behavior unless narrowed by policy” responds to another technical or business failure: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. That source case depends on: Routing protocol preference is broad selection behavior unless narrowed by policy. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “Policy routing can override ordinary destination lookup but still requires valid forwarding resolution” because Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.

B:

“ACL enforcement is sensitive to attachment location and traffic direction” responds to another technical or business failure: An administrator applies an ACL to an ingress interface in the wrong direction and a blocked flow still reaches servers. That source case depends on: ACL enforcement is sensitive to attachment location and traffic direction. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “Policy routing can override ordinary destination lookup but still requires valid forwarding resolution” because Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.

D:

“Policy association points control which imported routing information is modified” responds to another technical or business failure: An import routing policy changes route preference globally when only one partner's redistributed routes should be affected. That source case depends on: Policy association points control which imported routing information is modified. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “Policy routing can override ordinary destination lookup but still requires valid forwarding resolution” because Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.

Question 354

At fictional Timberline Operations, a network engineer supporting production campuses is reviewing route-policy and traffic-control behavior during a controlled failover exercise (HCIP-H12-821-POLICY-089). The observed network issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. Which ongoing preventive or detective control would best reduce recurrence?

  1. Test PBR failover and unresolved-next-hop behavior in a controlled environment.
  2. Audit redistributed origin tags and filter sequences at each protocol boundary.
  3. Review external route inventory after every redistribution expansion.
  4. Maintain interface direction diagrams alongside traffic-filter rules.

Explanation

Correct Answer

A:

The preventive or detective safeguard is: Test PBR failover and unresolved-next-hop behavior in a controlled environment. This directly addresses the recurring fault: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The corrective action would be: Correct next-hop reachability and routing-instance association before retaining the policy. Success is demonstrated when: PBR-selected test packets follow a reachable authorized next hop without black holes.

Incorrect Answers

B:

“Audit redistributed origin tags and filter sequences at each protocol boundary” addresses recurrence of another problem: An engineer imports routes from a backup routing process without a loop-prevention tag and the same prefixes circulate between protocols. That problem depends on: The preventive or detective safeguard is: Audit redistributed origin tags and filter sequences at each protocol boundary. The recurring risk here is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more targeted safeguard is “Test PBR failover and unresolved-next-hop behavior in a controlled environment” because the preventive or detective safeguard is: Test PBR failover and unresolved-next-hop behavior in a controlled environment.

C:

“Review external route inventory after every redistribution expansion” addresses recurrence of another problem: A site redistributes static routes into OSPF and accidentally advertises a management-only address to every area. That problem depends on: The preventive or detective safeguard is: Review external route inventory after every redistribution expansion. The recurring risk here is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more targeted safeguard is “Test PBR failover and unresolved-next-hop behavior in a controlled environment” because the preventive or detective safeguard is: Test PBR failover and unresolved-next-hop behavior in a controlled environment.

D:

“Maintain interface direction diagrams alongside traffic-filter rules” addresses recurrence of another problem: An administrator applies an ACL to an ingress interface in the wrong direction and a blocked flow still reaches servers. That problem depends on: The preventive or detective safeguard is: Maintain interface direction diagrams alongside traffic-filter rules. The recurring risk here is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more targeted safeguard is “Test PBR failover and unresolved-next-hop behavior in a controlled environment” because the preventive or detective safeguard is: Test PBR failover and unresolved-next-hop behavior in a controlled environment.

Question 355

At fictional Timberline Operations, a network engineer supporting production campuses is reviewing route-policy and traffic-control behavior during a controlled failover exercise (HCIP-H12-821-POLICY-089). The observed network issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. Which next engineering action best addresses the reported problem?

  1. Review route-policy node sequence and permit or deny outcomes for matching and unmatched routes.
  2. Narrow route-policy scope to the intended neighbor, protocol and prefix sets.
  3. Correct next-hop reachability and routing-instance association before retaining the policy.
  4. Mark redistributed routes and block re-import at reciprocal protocol boundaries.

Explanation

Correct Answer

C:

The directly responsive action is: Correct next-hop reachability and routing-instance association before retaining the policy. The specific reported fault is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. Confirmation should show: PBR-selected test packets follow a reachable authorized next hop without black holes. The supporting technical principle is: Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.

Incorrect Answers

A:

“Review route-policy node sequence and permit or deny outcomes for matching and unmatched routes” responds to another technical or business failure: A Huawei route-policy matches a prefix but the engineer expects every route passing the first node to continue through later nodes. That source case depends on: Ordered route policies evaluate match conditions and actions rather than combining all nodes indiscriminately. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “Correct next-hop reachability and routing-instance association before retaining the policy” because Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.

B:

“Narrow route-policy scope to the intended neighbor, protocol and prefix sets” responds to another technical or business failure: An import routing policy changes route preference globally when only one partner's redistributed routes should be affected. That source case depends on: Policy association points control which imported routing information is modified. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “Correct next-hop reachability and routing-instance association before retaining the policy” because Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.

D:

“Mark redistributed routes and block re-import at reciprocal protocol boundaries” responds to another technical or business failure: An engineer imports routes from a backup routing process without a loop-prevention tag and the same prefixes circulate between protocols. That source case depends on: Bidirectional route redistribution requires loop prevention and consistent route ownership. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “Correct next-hop reachability and routing-instance association before retaining the policy” because Policy routing can override ordinary destination lookup but still requires valid forwarding resolution.

Question 356

At fictional Timberline Operations, a network engineer supporting production campuses is reviewing route-policy and traffic-control behavior during a controlled failover exercise (HCIP-H12-821-POLICY-089). The observed network issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. Which observation most directly verifies that the corrective change succeeded?

  1. Upstream observed updates carry permitted communities and service-specific actions occur.
  2. Voice delay remains within service objectives without starving lower-priority classes.
  3. Measured loss and rate follow the intended policing or shaping design under overload.
  4. PBR-selected test packets follow a reachable authorized next hop without black holes.

Explanation

Correct Answer

D:

The best verification observation is: PBR-selected test packets follow a reachable authorized next hop without black holes. It demonstrates the corrective action: Correct next-hop reachability and routing-instance association before retaining the policy. This fits the principle: Policy routing can override ordinary destination lookup but still requires valid forwarding resolution. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Upstream observed updates carry permitted communities and service-specific actions occur” responds to another technical or business failure: An outbound route-policy appends a community but the upstream device removes communities when send behavior is disabled. That source case depends on: The best verification observation is: Upstream observed updates carry permitted communities and service-specific actions occur. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “PBR-selected test packets follow a reachable authorized next hop without black holes” because the best verification observation is: PBR-selected test packets follow a reachable authorized next hop without black holes.

B:

“Voice delay remains within service objectives without starving lower-priority classes” responds to another technical or business failure: A campus egress port uses weighted scheduling but latency-sensitive voice sits behind large bulk transfers. That source case depends on: The best verification observation is: Voice delay remains within service objectives without starving lower-priority classes. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “PBR-selected test packets follow a reachable authorized next hop without black holes” because the best verification observation is: PBR-selected test packets follow a reachable authorized next hop without black holes.

C:

“Measured loss and rate follow the intended policing or shaping design under overload” responds to another technical or business failure: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. That source case depends on: The best verification observation is: Measured loss and rate follow the intended policing or shaping design under overload. The present issue is: A policy-based routing rule sends traffic toward a next hop that cannot be resolved in the correct VRF. The more direct action is “PBR-selected test packets follow a reachable authorized next hop without black holes” because the best verification observation is: PBR-selected test packets follow a reachable authorized next hop without black holes.

Question 357

At fictional Maple Housing, a network engineer supporting property locations is reviewing IGMP and PIM multicast distribution during a supervised route change (HCIP-H12-821-MULTICAST-090). The observed network issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. Which next engineering action best addresses the reported problem?

  1. Check reverse path to the source and verify supported SPT switching behavior.
  2. Assign unique approved group ranges and check IGMP or PIM subscriptions.
  3. Repair or accelerate intended unicast convergence and validate multicast state reevaluation.
  4. Align IGMP version support and receiver source-filtering expectations.

Explanation

Correct Answer

C:

The directly responsive action is: Repair or accelerate intended unicast convergence and validate multicast state reevaluation. The specific reported fault is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. Confirmation should show: Multicast packets resume on the revised valid RPF interface after failover. The supporting technical principle is: Multicast forwarding depends on current unicast or multicast RPF route calculation.

Incorrect Answers

A:

“Check reverse path to the source and verify supported SPT switching behavior” responds to another technical or business failure: A PIM-SM router cannot switch efficiently to a shortest-path tree because its source route points through another neighbor. That source case depends on: PIM-SM can transition from an RP shared tree to a source-specific shortest-path tree. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Repair or accelerate intended unicast convergence and validate multicast state reevaluation” because Multicast forwarding depends on current unicast or multicast RPF route calculation.

B:

“Assign unique approved group ranges and check IGMP or PIM subscriptions” responds to another technical or business failure: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. That source case depends on: Multicast group addressing must be managed as an intentional shared network namespace. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Repair or accelerate intended unicast convergence and validate multicast state reevaluation” because Multicast forwarding depends on current unicast or multicast RPF route calculation.

D:

“Align IGMP version support and receiver source-filtering expectations” responds to another technical or business failure: A network expects IGMPv3 source-specific filtering but uses routers configured only for IGMPv2. That source case depends on: IGMPv3 adds source filtering required for source-specific multicast operation. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Repair or accelerate intended unicast convergence and validate multicast state reevaluation” because Multicast forwarding depends on current unicast or multicast RPF route calculation.

Question 358

At fictional Maple Housing, a network engineer supporting property locations is reviewing IGMP and PIM multicast distribution during a supervised route change (HCIP-H12-821-MULTICAST-090). The observed network issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. Which routing, switching, or network principle best explains the appropriate solution?

  1. SSM receivers identify the source and group and avoid general ASM RP discovery.
  2. PIM forwarding state should track downstream interest and prune unused paths.
  3. Multicast forwarding depends on current unicast or multicast RPF route calculation.
  4. Multicast routing uses reverse-path-forwarding checks to prevent loops.

Explanation

Correct Answer

C:

The governing principle is: Multicast forwarding depends on current unicast or multicast RPF route calculation. In this scenario, the appropriate action is: Repair or accelerate intended unicast convergence and validate multicast state reevaluation. Valid evidence would show: Multicast packets resume on the revised valid RPF interface after failover.

Incorrect Answers

A:

“SSM receivers identify the source and group and avoid general ASM RP discovery” responds to another technical or business failure: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. That source case depends on: SSM receivers identify the source and group and avoid general ASM RP discovery. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Multicast forwarding depends on current unicast or multicast RPF route calculation” because Multicast forwarding depends on current unicast or multicast RPF route calculation.

B:

“PIM forwarding state should track downstream interest and prune unused paths” responds to another technical or business failure: An upstream router continuously forwards multicast after a branch has no receivers because PIM prune information is missing. That source case depends on: PIM forwarding state should track downstream interest and prune unused paths. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Multicast forwarding depends on current unicast or multicast RPF route calculation” because Multicast forwarding depends on current unicast or multicast RPF route calculation.

D:

“Multicast routing uses reverse-path-forwarding checks to prevent loops” responds to another technical or business failure: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. That source case depends on: Multicast routing uses reverse-path-forwarding checks to prevent loops. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Multicast forwarding depends on current unicast or multicast RPF route calculation” because Multicast forwarding depends on current unicast or multicast RPF route calculation.

Question 359

At fictional Maple Housing, a network engineer supporting property locations is reviewing IGMP and PIM multicast distribution during a supervised route change (HCIP-H12-821-MULTICAST-090). The observed network issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. Which observation most directly verifies that the corrective change succeeded?

  1. Client memberships are refreshed and multicast packets reach subscribed hosts.
  2. Multicast packets resume on the revised valid RPF interface after failover.
  3. Only the requested source-group stream is delivered without RP-based ambiguity.
  4. Unsubscribed branches no longer receive unnecessary streams after PIM state convergence.

Explanation

Correct Answer

B:

The best verification observation is: Multicast packets resume on the revised valid RPF interface after failover. It demonstrates the corrective action: Repair or accelerate intended unicast convergence and validate multicast state reevaluation. This fits the principle: Multicast forwarding depends on current unicast or multicast RPF route calculation. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Client memberships are refreshed and multicast packets reach subscribed hosts” responds to another technical or business failure: A multicast router sees no group receivers because IGMP query messages are absent from a VLAN. That source case depends on: The best verification observation is: Client memberships are refreshed and multicast packets reach subscribed hosts. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Multicast packets resume on the revised valid RPF interface after failover” because the best verification observation is: Multicast packets resume on the revised valid RPF interface after failover.

C:

“Only the requested source-group stream is delivered without RP-based ambiguity” responds to another technical or business failure: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. That source case depends on: The best verification observation is: Only the requested source-group stream is delivered without RP-based ambiguity. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Multicast packets resume on the revised valid RPF interface after failover” because the best verification observation is: Multicast packets resume on the revised valid RPF interface after failover.

D:

“Unsubscribed branches no longer receive unnecessary streams after PIM state convergence” responds to another technical or business failure: A PIM dense-mode network floods large multicast volumes to branches with no interested receivers. That source case depends on: The best verification observation is: Unsubscribed branches no longer receive unnecessary streams after PIM state convergence. The present issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more direct action is “Multicast packets resume on the revised valid RPF interface after failover” because the best verification observation is: Multicast packets resume on the revised valid RPF interface after failover.

Question 360

At fictional Maple Housing, a network engineer supporting property locations is reviewing IGMP and PIM multicast distribution during a supervised route change (HCIP-H12-821-MULTICAST-090). The observed network issue is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. Which ongoing preventive or detective control would best reduce recurrence?

  1. Test source-route failure recovery for multicast services.
  2. Validate snooping memberships after each VLAN access change.
  3. Record IGMP version compatibility for source-filtered applications.
  4. Include explicit (source, group) joins in SSM acceptance tests.

Explanation

Correct Answer

A:

The preventive or detective safeguard is: Test source-route failure recovery for multicast services. This directly addresses the recurring fault: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The corrective action would be: Repair or accelerate intended unicast convergence and validate multicast state reevaluation. Success is demonstrated when: Multicast packets resume on the revised valid RPF interface after failover.

Incorrect Answers

B:

“Validate snooping memberships after each VLAN access change” addresses recurrence of another problem: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. That problem depends on: The preventive or detective safeguard is: Validate snooping memberships after each VLAN access change. The recurring risk here is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more targeted safeguard is “Test source-route failure recovery for multicast services” because the preventive or detective safeguard is: Test source-route failure recovery for multicast services.

C:

“Record IGMP version compatibility for source-filtered applications” addresses recurrence of another problem: A network expects IGMPv3 source-specific filtering but uses routers configured only for IGMPv2. That problem depends on: The preventive or detective safeguard is: Record IGMP version compatibility for source-filtered applications. The recurring risk here is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more targeted safeguard is “Test source-route failure recovery for multicast services” because the preventive or detective safeguard is: Test source-route failure recovery for multicast services.

D:

“Include explicit (source, group) joins in SSM acceptance tests” addresses recurrence of another problem: A source-specific multicast receiver attempts to use an any-source RP tree even though the deployment expects a specified source. That problem depends on: The preventive or detective safeguard is: Include explicit (source, group) joins in SSM acceptance tests. The recurring risk here is: A multicast core drops packets after a path failover because the unicast RPF route has not converged to the new incoming link. The more targeted safeguard is “Test source-route failure recovery for multicast services” because the preventive or detective safeguard is: Test source-route failure recovery for multicast services.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests