McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 67

Question 660

At fictional Keystone Hospitality, a network engineer supporting guest services is reviewing controller-managed enterprise WLAN during a production cutover (HCIP-H12-821-WLAN-165). The observed network issue is: A large WLAN loses client services during AC maintenance because all APs depend on a single unprotected controller. Which routing, switching, or network principle best explains the appropriate solution?

  1. WLAN roaming outcomes depend on consistent client network mapping and mobility design.
  2. WLAN controller profiles become effective only when associated with the correct AP scope.
  3. WLAN radio cell size influences roaming decisions and co-channel interference.
  4. Centralized WLAN control needs deliberate high availability and AP failover planning.

Explanation

Correct Answer

D:

The governing principle is: Centralized WLAN control needs deliberate high availability and AP failover planning. In this scenario, the appropriate action is: Design supported AC redundancy and AP failover behavior and verify its licensing and topology. Valid evidence would show: APs recover onto the intended backup AC and approved SSIDs resume service.

Incorrect Answers

A:

“WLAN roaming outcomes depend on consistent client network mapping and mobility design” responds to another technical or business failure: Users roam between APs but lose sessions because the target AP maps the same SSID to a different unplanned VLAN. That source case depends on: WLAN roaming outcomes depend on consistent client network mapping and mobility design. The present issue is: A large WLAN loses client services during AC maintenance because all APs depend on a single unprotected controller. The more direct action is “Centralized WLAN control needs deliberate high availability and AP failover planning” because Centralized WLAN control needs deliberate high availability and AP failover planning.

B:

“WLAN controller profiles become effective only when associated with the correct AP scope” responds to another technical or business failure: An AC service template is correct but an AP group still advertises an old SSID due to an unbound or wrong profile. That source case depends on: WLAN controller profiles become effective only when associated with the correct AP scope. The present issue is: A large WLAN loses client services during AC maintenance because all APs depend on a single unprotected controller. The more direct action is “Centralized WLAN control needs deliberate high availability and AP failover planning” because Centralized WLAN control needs deliberate high availability and AP failover planning.

C:

“WLAN radio cell size influences roaming decisions and co-channel interference” responds to another technical or business failure: A Wi-Fi deployment applies identical power levels in a dense conference center and clients roam unpredictably to distant APs. That source case depends on: WLAN radio cell size influences roaming decisions and co-channel interference. The present issue is: A large WLAN loses client services during AC maintenance because all APs depend on a single unprotected controller. The more direct action is “Centralized WLAN control needs deliberate high availability and AP failover planning” because Centralized WLAN control needs deliberate high availability and AP failover planning.

Question 661

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing route-policy and traffic-control behavior during an initial deployment test (HCIP-H12-821-POLICY-166). The observed network issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. Which routing, switching, or network principle best explains the appropriate solution?

  1. Traffic policing and traffic shaping handle excess rates differently.
  2. Policy association points control which imported routing information is modified.
  3. Token bucket policers classify traffic using configured rate and burst parameters.
  4. Egress congestion scheduling determines queuing delay among traffic classes.

Explanation

Correct Answer

A:

The governing principle is: Traffic policing and traffic shaping handle excess rates differently. In this scenario, the appropriate action is: Distinguish policing drop or remark actions from shaping that buffers traffic over time. Valid evidence would show: Measured loss and rate follow the intended policing or shaping design under overload.

Incorrect Answers

B:

“Policy association points control which imported routing information is modified” responds to another technical or business failure: An import routing policy changes route preference globally when only one partner's redistributed routes should be affected. That source case depends on: Policy association points control which imported routing information is modified. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Traffic policing and traffic shaping handle excess rates differently” because Traffic policing and traffic shaping handle excess rates differently.

C:

“Token bucket policers classify traffic using configured rate and burst parameters” responds to another technical or business failure: A WAN traffic policy drops packets after a bandwidth threshold because committed and excess rates were configured incorrectly. That source case depends on: Token bucket policers classify traffic using configured rate and burst parameters. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Traffic policing and traffic shaping handle excess rates differently” because Traffic policing and traffic shaping handle excess rates differently.

D:

“Egress congestion scheduling determines queuing delay among traffic classes” responds to another technical or business failure: A campus egress port uses weighted scheduling but latency-sensitive voice sits behind large bulk transfers. That source case depends on: Egress congestion scheduling determines queuing delay among traffic classes. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Traffic policing and traffic shaping handle excess rates differently” because Traffic policing and traffic shaping handle excess rates differently.

Question 662

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing route-policy and traffic-control behavior during an initial deployment test (HCIP-H12-821-POLICY-166). The observed network issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. Which ongoing preventive or detective control would best reduce recurrence?

  1. Check trust boundary and classification counters before measuring QoS outcome.
  2. Build source-destination acceptance matrices for policy-based routing.
  3. Compare affected prefixes and VRF scope before changing route preference.
  4. Validate policer and shaper action selection against traffic SLAs.

Explanation

Correct Answer

D:

The preventive or detective safeguard is: Validate policer and shaper action selection against traffic SLAs. This directly addresses the recurring fault: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The corrective action would be: Distinguish policing drop or remark actions from shaping that buffers traffic over time. Success is demonstrated when: Measured loss and rate follow the intended policing or shaping design under overload.

Incorrect Answers

A:

“Check trust boundary and classification counters before measuring QoS outcome” addresses recurrence of another problem: A classifier matches the wrong VLAN priority bits and high-priority voice is treated as bulk data. That problem depends on: The preventive or detective safeguard is: Check trust boundary and classification counters before measuring QoS outcome. The recurring risk here is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more targeted safeguard is “Validate policer and shaper action selection against traffic SLAs” because the preventive or detective safeguard is: Validate policer and shaper action selection against traffic SLAs.

B:

“Build source-destination acceptance matrices for policy-based routing” addresses recurrence of another problem: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. That problem depends on: The preventive or detective safeguard is: Build source-destination acceptance matrices for policy-based routing. The recurring risk here is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more targeted safeguard is “Validate policer and shaper action selection against traffic SLAs” because the preventive or detective safeguard is: Validate policer and shaper action selection against traffic SLAs.

C:

“Compare affected prefixes and VRF scope before changing route preference” addresses recurrence of another problem: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. That problem depends on: The preventive or detective safeguard is: Compare affected prefixes and VRF scope before changing route preference. The recurring risk here is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more targeted safeguard is “Validate policer and shaper action selection against traffic SLAs” because the preventive or detective safeguard is: Validate policer and shaper action selection against traffic SLAs.

Question 663

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing route-policy and traffic-control behavior during an initial deployment test (HCIP-H12-821-POLICY-166). The observed network issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. Which observation most directly verifies that the corrective change succeeded?

  1. Voice packets hit the intended class and maintain lower delay during controlled congestion.
  2. Measured loss and rate follow the intended policing or shaping design under overload.
  3. Controlled traffic shows desired throughput and measured color actions without unexpected loss.
  4. OSPF external LSAs exclude the management subnet and include permitted service destinations.

Explanation

Correct Answer

B:

The best verification observation is: Measured loss and rate follow the intended policing or shaping design under overload. It demonstrates the corrective action: Distinguish policing drop or remark actions from shaping that buffers traffic over time. This fits the principle: Traffic policing and traffic shaping handle excess rates differently. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Voice packets hit the intended class and maintain lower delay during controlled congestion” responds to another technical or business failure: A classifier matches the wrong VLAN priority bits and high-priority voice is treated as bulk data. That source case depends on: The best verification observation is: Voice packets hit the intended class and maintain lower delay during controlled congestion. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Measured loss and rate follow the intended policing or shaping design under overload” because the best verification observation is: Measured loss and rate follow the intended policing or shaping design under overload.

C:

“Controlled traffic shows desired throughput and measured color actions without unexpected loss” responds to another technical or business failure: A WAN traffic policy drops packets after a bandwidth threshold because committed and excess rates were configured incorrectly. That source case depends on: The best verification observation is: Controlled traffic shows desired throughput and measured color actions without unexpected loss. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Measured loss and rate follow the intended policing or shaping design under overload” because the best verification observation is: Measured loss and rate follow the intended policing or shaping design under overload.

D:

“OSPF external LSAs exclude the management subnet and include permitted service destinations” responds to another technical or business failure: A site redistributes static routes into OSPF and accidentally advertises a management-only address to every area. That source case depends on: The best verification observation is: OSPF external LSAs exclude the management subnet and include permitted service destinations. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Measured loss and rate follow the intended policing or shaping design under overload” because the best verification observation is: Measured loss and rate follow the intended policing or shaping design under overload.

Question 664

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing route-policy and traffic-control behavior during an initial deployment test (HCIP-H12-821-POLICY-166). The observed network issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. Which next engineering action best addresses the reported problem?

  1. Mark redistributed routes and block re-import at reciprocal protocol boundaries.
  2. Distinguish policing drop or remark actions from shaping that buffers traffic over time.
  3. Fix the traffic-class match conditions and map approved markings to correct queues.
  4. Verify outbound community transmission settings on the peer and acceptance policy.

Explanation

Correct Answer

B:

The directly responsive action is: Distinguish policing drop or remark actions from shaping that buffers traffic over time. The specific reported fault is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. Confirmation should show: Measured loss and rate follow the intended policing or shaping design under overload. The supporting technical principle is: Traffic policing and traffic shaping handle excess rates differently.

Incorrect Answers

A:

“Mark redistributed routes and block re-import at reciprocal protocol boundaries” responds to another technical or business failure: An engineer imports routes from a backup routing process without a loop-prevention tag and the same prefixes circulate between protocols. That source case depends on: Bidirectional route redistribution requires loop prevention and consistent route ownership. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Distinguish policing drop or remark actions from shaping that buffers traffic over time” because Traffic policing and traffic shaping handle excess rates differently.

C:

“Fix the traffic-class match conditions and map approved markings to correct queues” responds to another technical or business failure: A classifier matches the wrong VLAN priority bits and high-priority voice is treated as bulk data. That source case depends on: QoS behavior begins with accurate classification of relevant traffic fields. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Distinguish policing drop or remark actions from shaping that buffers traffic over time” because Traffic policing and traffic shaping handle excess rates differently.

D:

“Verify outbound community transmission settings on the peer and acceptance policy” responds to another technical or business failure: An outbound route-policy appends a community but the upstream device removes communities when send behavior is disabled. That source case depends on: Route attribute creation alone does not guarantee propagation across a BGP session. The present issue is: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. The more direct action is “Distinguish policing drop or remark actions from shaping that buffers traffic over time” because Traffic policing and traffic shaping handle excess rates differently.

Question 665

At fictional Oakridge Energy, a network engineer supporting field substations is reviewing VRRP, BFD and redundancy design during a baseline compliance test (HCIP-H12-821-RELIABILITY-167). The observed network issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. Which next engineering action best addresses the reported problem?

  1. Configure supported VRRP uplink tracking and suitable priority decrement.
  2. Redesign independent backup next-hop reachability and validate actual alternate path availability.
  3. Identify shared physical dependencies and add independent power or placement where feasible.
  4. Verify VRRP virtual address, group identifiers and ARP or ND mapping as supported.

Explanation

Correct Answer

C:

The directly responsive action is: Identify shared physical dependencies and add independent power or placement where feasible. The specific reported fault is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. Confirmation should show: Controlled loss of one supply feed preserves the defined critical forwarding service. The supporting technical principle is: Network reliability depends on eliminating shared risks, not only duplicating network devices.

Incorrect Answers

A:

“Configure supported VRRP uplink tracking and suitable priority decrement” responds to another technical or business failure: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. That source case depends on: VRRP interface or route tracking can couple gateway priority to actual upstream health. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Identify shared physical dependencies and add independent power or placement where feasible” because Network reliability depends on eliminating shared risks, not only duplicating network devices.

B:

“Redesign independent backup next-hop reachability and validate actual alternate path availability” responds to another technical or business failure: An interface failure is detected rapidly by BFD but the backup route points to the same failed upstream dependency. That source case depends on: Fast fault detection is ineffective without a genuinely independent recovery path. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Identify shared physical dependencies and add independent power or placement where feasible” because Network reliability depends on eliminating shared risks, not only duplicating network devices.

D:

“Verify VRRP virtual address, group identifiers and ARP or ND mapping as supported” responds to another technical or business failure: Two edge routers use independent VRRP groups with conflicting virtual MAC expectations and clients intermittently lose connectivity. That source case depends on: Virtual gateway addressing and neighbor-cache convergence influence failover traffic. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Identify shared physical dependencies and add independent power or placement where feasible” because Network reliability depends on eliminating shared risks, not only duplicating network devices.

Question 666

At fictional Oakridge Energy, a network engineer supporting field substations is reviewing VRRP, BFD and redundancy design during a baseline compliance test (HCIP-H12-821-RELIABILITY-167). The observed network issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. Which observation most directly verifies that the corrective change succeeded?

  1. The routing session or route promptly reacts when BFD detects forwarding failure.
  2. Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address.
  3. Failure detection meets the service objective without spurious adjacency resets.
  4. Controlled loss of one supply feed preserves the defined critical forwarding service.

Explanation

Correct Answer

D:

The best verification observation is: Controlled loss of one supply feed preserves the defined critical forwarding service. It demonstrates the corrective action: Identify shared physical dependencies and add independent power or placement where feasible. This fits the principle: Network reliability depends on eliminating shared risks, not only duplicating network devices. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“The routing session or route promptly reacts when BFD detects forwarding failure” responds to another technical or business failure: A router forwards to a remote next hop even after its BGP peer's far-end forwarding path is lost, causing slow detection. That source case depends on: The best verification observation is: The routing session or route promptly reacts when BFD detects forwarding failure. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Controlled loss of one supply feed preserves the defined critical forwarding service” because the best verification observation is: Controlled loss of one supply feed preserves the defined critical forwarding service.

B:

“Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address” responds to another technical or business failure: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. That source case depends on: The best verification observation is: Loss of the tracked path leads to the intended gateway failover while user hosts retain their virtual address. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Controlled loss of one supply feed preserves the defined critical forwarding service” because the best verification observation is: Controlled loss of one supply feed preserves the defined critical forwarding service.

C:

“Failure detection meets the service objective without spurious adjacency resets” responds to another technical or business failure: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. That source case depends on: The best verification observation is: Failure detection meets the service objective without spurious adjacency resets. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Controlled loss of one supply feed preserves the defined critical forwarding service” because the best verification observation is: Controlled loss of one supply feed preserves the defined critical forwarding service.

Question 667

At fictional Oakridge Energy, a network engineer supporting field substations is reviewing VRRP, BFD and redundancy design during a baseline compliance test (HCIP-H12-821-RELIABILITY-167). The observed network issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. Which routing, switching, or network principle best explains the appropriate solution?

  1. Gateway availability and end-to-end network reachability are different reliability properties.
  2. Network reliability depends on eliminating shared risks, not only duplicating network devices.
  3. Virtual gateway addressing and neighbor-cache convergence influence failover traffic.
  4. VRRP interface or route tracking can couple gateway priority to actual upstream health.

Explanation

Correct Answer

B:

The governing principle is: Network reliability depends on eliminating shared risks, not only duplicating network devices. In this scenario, the appropriate action is: Identify shared physical dependencies and add independent power or placement where feasible. Valid evidence would show: Controlled loss of one supply feed preserves the defined critical forwarding service.

Incorrect Answers

A:

“Gateway availability and end-to-end network reachability are different reliability properties” responds to another technical or business failure: A VRRP virtual IP responds locally but remote services fail because both gateway uplinks have lost their default route. That source case depends on: Gateway availability and end-to-end network reachability are different reliability properties. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Network reliability depends on eliminating shared risks, not only duplicating network devices” because Network reliability depends on eliminating shared risks, not only duplicating network devices.

C:

“Virtual gateway addressing and neighbor-cache convergence influence failover traffic” responds to another technical or business failure: Two edge routers use independent VRRP groups with conflicting virtual MAC expectations and clients intermittently lose connectivity. That source case depends on: Virtual gateway addressing and neighbor-cache convergence influence failover traffic. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Network reliability depends on eliminating shared risks, not only duplicating network devices” because Network reliability depends on eliminating shared risks, not only duplicating network devices.

D:

“VRRP interface or route tracking can couple gateway priority to actual upstream health” responds to another technical or business failure: A VRRP standby router never becomes master after the preferred uplink fails because only the physical LAN interface remains Up. That source case depends on: VRRP interface or route tracking can couple gateway priority to actual upstream health. The present issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more direct action is “Network reliability depends on eliminating shared risks, not only duplicating network devices” because Network reliability depends on eliminating shared risks, not only duplicating network devices.

Question 668

At fictional Oakridge Energy, a network engineer supporting field substations is reviewing VRRP, BFD and redundancy design during a baseline compliance test (HCIP-H12-821-RELIABILITY-167). The observed network issue is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. Which ongoing preventive or detective control would best reduce recurrence?

  1. Test member and uplink loss separately in stack design validation.
  2. Test VRRP master and backup roles during campus change acceptance.
  3. Measure detection and end-to-end recovery rather than relying on configured timer values.
  4. Audit power and physical path diversity alongside protocol failover tests.

Explanation

Correct Answer

D:

The preventive or detective safeguard is: Audit power and physical path diversity alongside protocol failover tests. This directly addresses the recurring fault: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The corrective action would be: Identify shared physical dependencies and add independent power or placement where feasible. Success is demonstrated when: Controlled loss of one supply feed preserves the defined critical forwarding service.

Incorrect Answers

A:

“Test member and uplink loss separately in stack design validation” addresses recurrence of another problem: A switch stack offers redundant members but its sole uplink attaches to one device and remains a failure point. That problem depends on: The preventive or detective safeguard is: Test member and uplink loss separately in stack design validation. The recurring risk here is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more targeted safeguard is “Audit power and physical path diversity alongside protocol failover tests” because the preventive or detective safeguard is: Audit power and physical path diversity alongside protocol failover tests.

B:

“Test VRRP master and backup roles during campus change acceptance” addresses recurrence of another problem: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. That problem depends on: The preventive or detective safeguard is: Test VRRP master and backup roles during campus change acceptance. The recurring risk here is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more targeted safeguard is “Audit power and physical path diversity alongside protocol failover tests” because the preventive or detective safeguard is: Audit power and physical path diversity alongside protocol failover tests.

C:

“Measure detection and end-to-end recovery rather than relying on configured timer values” addresses recurrence of another problem: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. That problem depends on: The preventive or detective safeguard is: Measure detection and end-to-end recovery rather than relying on configured timer values. The recurring risk here is: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. The more targeted safeguard is “Audit power and physical path diversity alongside protocol failover tests” because the preventive or detective safeguard is: Audit power and physical path diversity alongside protocol failover tests.

Question 669

At fictional Alder Community, a network engineer supporting regional administration is reviewing router control and forwarding planes during a supervised route change (HCIP-H12-821-ROUTING-168). The observed network issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. Which ongoing preventive or detective control would best reduce recurrence?

  1. Audit static route VRF association and next-hop reachability after migrations.
  2. Verify forwarding-plane installation as well as route reception during changes.
  3. Validate Type 7 generation and ABR translation during branch redistribution testing.
  4. Test VLAN loop avoidance and default gateway failover separately.

Explanation

Correct Answer

A:

The preventive or detective safeguard is: Audit static route VRF association and next-hop reachability after migrations. This directly addresses the recurring fault: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The corrective action would be: Verify each static next hop resolves in the intended routing instance and compare qualified route preference. Success is demonstrated when: The primary route is active in the intended table and the backup only becomes active when needed.

Incorrect Answers

B:

“Verify forwarding-plane installation as well as route reception during changes” addresses recurrence of another problem: A network operator believes a route present in the routing information base must already be programmed into every forwarding ASIC. That problem depends on: The preventive or detective safeguard is: Verify forwarding-plane installation as well as route reception during changes. The recurring risk here is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more targeted safeguard is “Audit static route VRF association and next-hop reachability after migrations” because the preventive or detective safeguard is: Audit static route VRF association and next-hop reachability after migrations.

C:

“Validate Type 7 generation and ABR translation during branch redistribution testing” addresses recurrence of another problem: An NSSA branch redistributes a local service prefix but the backbone never receives the route. That problem depends on: The preventive or detective safeguard is: Validate Type 7 generation and ABR translation during branch redistribution testing. The recurring risk here is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more targeted safeguard is “Audit static route VRF association and next-hop reachability after migrations” because the preventive or detective safeguard is: Audit static route VRF association and next-hop reachability after migrations.

D:

“Test VLAN loop avoidance and default gateway failover separately” addresses recurrence of another problem: A team expects MSTP instance root selection to affect layer-3 inter-VLAN gateway ownership automatically. That problem depends on: The preventive or detective safeguard is: Test VLAN loop avoidance and default gateway failover separately. The recurring risk here is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more targeted safeguard is “Audit static route VRF association and next-hop reachability after migrations” because the preventive or detective safeguard is: Audit static route VRF association and next-hop reachability after migrations.

Question 670

At fictional Alder Community, a network engineer supporting regional administration is reviewing router control and forwarding planes during a supervised route change (HCIP-H12-821-ROUTING-168). The observed network issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. Which routing, switching, or network principle best explains the appropriate solution?

  1. A valid routing control decision must be verified against actual forwarding behavior.
  2. DHCP option delivery configures host network behavior beyond simple address assignment.
  3. Route installation depends on routing-instance scope and next-hop resolution as well as preference.
  4. IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport.

Explanation

Correct Answer

C:

The governing principle is: Route installation depends on routing-instance scope and next-hop resolution as well as preference. In this scenario, the appropriate action is: Verify each static next hop resolves in the intended routing instance and compare qualified route preference. Valid evidence would show: The primary route is active in the intended table and the backup only becomes active when needed.

Incorrect Answers

A:

“A valid routing control decision must be verified against actual forwarding behavior” responds to another technical or business failure: An engineer changes a route policy but tests only the local routing table and overlooks downstream forwarding. That source case depends on: A valid routing control decision must be verified against actual forwarding behavior. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Route installation depends on routing-instance scope and next-hop resolution as well as preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

B:

“DHCP option delivery configures host network behavior beyond simple address assignment” responds to another technical or business failure: A DHCP pool provides the correct address block but clients cannot route because option 3 advertises the wrong default gateway. That source case depends on: DHCP option delivery configures host network behavior beyond simple address assignment. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Route installation depends on routing-instance scope and next-hop resolution as well as preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

D:

“IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport” responds to another technical or business failure: IS-IS adjacency remains Down when Hello frames are filtered by an intermediate layer-2 device. That source case depends on: IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Route installation depends on routing-instance scope and next-hop resolution as well as preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests