McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 68

Question 670

At fictional Alder Community, a network engineer supporting regional administration is reviewing router control and forwarding planes during a supervised route change (HCIP-H12-821-ROUTING-168). The observed network issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. Which routing, switching, or network principle best explains the appropriate solution?

  1. A valid routing control decision must be verified against actual forwarding behavior.
  2. DHCP option delivery configures host network behavior beyond simple address assignment.
  3. Route installation depends on routing-instance scope and next-hop resolution as well as preference.
  4. IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport.

Explanation

Correct Answer

C:

The governing principle is: Route installation depends on routing-instance scope and next-hop resolution as well as preference. In this scenario, the appropriate action is: Verify each static next hop resolves in the intended routing instance and compare qualified route preference. Valid evidence would show: The primary route is active in the intended table and the backup only becomes active when needed.

Incorrect Answers

A:

“A valid routing control decision must be verified against actual forwarding behavior” responds to another technical or business failure: An engineer changes a route policy but tests only the local routing table and overlooks downstream forwarding. That source case depends on: A valid routing control decision must be verified against actual forwarding behavior. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Route installation depends on routing-instance scope and next-hop resolution as well as preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

B:

“DHCP option delivery configures host network behavior beyond simple address assignment” responds to another technical or business failure: A DHCP pool provides the correct address block but clients cannot route because option 3 advertises the wrong default gateway. That source case depends on: DHCP option delivery configures host network behavior beyond simple address assignment. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Route installation depends on routing-instance scope and next-hop resolution as well as preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

D:

“IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport” responds to another technical or business failure: IS-IS adjacency remains Down when Hello frames are filtered by an intermediate layer-2 device. That source case depends on: IS-IS exchanges routing PDUs directly over the link rather than using ordinary IP multicast transport. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Route installation depends on routing-instance scope and next-hop resolution as well as preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

Question 671

At fictional Alder Community, a network engineer supporting regional administration is reviewing router control and forwarding planes during a supervised route change (HCIP-H12-821-ROUTING-168). The observed network issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. Which observation most directly verifies that the corrective change succeeded?

  1. Authorized identities connect to the WLAN while invalid credentials are denied.
  2. Both routers reach Established using the planned loopback source and destination.
  3. The RIB selects the intended route and the forwarding table has a corresponding installed next hop.
  4. The primary route is active in the intended table and the backup only becomes active when needed.

Explanation

Correct Answer

D:

The best verification observation is: The primary route is active in the intended table and the backup only becomes active when needed. It demonstrates the corrective action: Verify each static next hop resolves in the intended routing instance and compare qualified route preference. This fits the principle: Route installation depends on routing-instance scope and next-hop resolution as well as preference. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Authorized identities connect to the WLAN while invalid credentials are denied” responds to another technical or business failure: An SSID uses open authentication despite organizational requirements for enterprise identity verification. That source case depends on: The best verification observation is: Authorized identities connect to the WLAN while invalid credentials are denied. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “The primary route is active in the intended table and the backup only becomes active when needed” because the best verification observation is: The primary route is active in the intended table and the backup only becomes active when needed.

B:

“Both routers reach Established using the planned loopback source and destination” responds to another technical or business failure: An iBGP adjacency to peer loopbacks fails because one side sends TCP from the physical interface address. That source case depends on: The best verification observation is: Both routers reach Established using the planned loopback source and destination. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “The primary route is active in the intended table and the backup only becomes active when needed” because the best verification observation is: The primary route is active in the intended table and the backup only becomes active when needed.

C:

“The RIB selects the intended route and the forwarding table has a corresponding installed next hop” responds to another technical or business failure: A modular router has working interfaces but its line card forwarding statistics remain idle while the control CPU handles route updates. That source case depends on: The best verification observation is: The RIB selects the intended route and the forwarding table has a corresponding installed next hop. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “The primary route is active in the intended table and the backup only becomes active when needed” because the best verification observation is: The primary route is active in the intended table and the backup only becomes active when needed.

Question 672

At fictional Alder Community, a network engineer supporting regional administration is reviewing router control and forwarding planes during a supervised route change (HCIP-H12-821-ROUTING-168). The observed network issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. Which next engineering action best addresses the reported problem?

  1. Narrow permitted prefix filters to the approved route set and confirm the aggregate's precise prefix length.
  2. Trace prefix installation from routing protocol through RIB and FIB to a controlled end-to-end packet.
  3. Verify each static next hop resolves in the intended routing instance and compare qualified route preference.
  4. Apply longest-prefix matching before comparing administrative preference or metric among candidate routes.

Explanation

Correct Answer

C:

The directly responsive action is: Verify each static next hop resolves in the intended routing instance and compare qualified route preference. The specific reported fault is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. Confirmation should show: The primary route is active in the intended table and the backup only becomes active when needed. The supporting technical principle is: Route installation depends on routing-instance scope and next-hop resolution as well as preference.

Incorrect Answers

A:

“Narrow permitted prefix filters to the approved route set and confirm the aggregate's precise prefix length” responds to another technical or business failure: An administrator applies an export prefix list at the BGP border but mistakenly filters all networks including a critical aggregate. That source case depends on: BGP outbound prefix filtering controls which NLRI are advertised to external peers. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Verify each static next hop resolves in the intended routing instance and compare qualified route preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

B:

“Trace prefix installation from routing protocol through RIB and FIB to a controlled end-to-end packet” responds to another technical or business failure: An engineer changes a route policy but tests only the local routing table and overlooks downstream forwarding. That source case depends on: A valid routing control decision must be verified against actual forwarding behavior. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Verify each static next hop resolves in the intended routing instance and compare qualified route preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

D:

“Apply longest-prefix matching before comparing administrative preference or metric among candidate routes” responds to another technical or business failure: Two routes cover a remote host and an engineer expects the less-specific default route to take precedence. That source case depends on: Forwarding selects the longest matching destination prefix before considering route preferences. The present issue is: A backup static route takes over even though the preferred next hop is still reachable in the wrong VRF. The more direct action is “Verify each static next hop resolves in the intended routing instance and compare qualified route preference” because Route installation depends on routing-instance scope and next-hop resolution as well as preference.

Question 673

At fictional Elmstone Transit, a network engineer supporting operations terminals is reviewing VRRP, BFD and redundancy design during a planned network scaling change (HCIP-H12-821-RELIABILITY-169). The observed network issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. Which routing, switching, or network principle best explains the appropriate solution?

  1. VRRP coordinates virtual default-gateway ownership among participating routers.
  2. VRRP priority and preemption behavior are separate configured failover choices.
  3. Virtual gateway addressing and neighbor-cache convergence influence failover traffic.
  4. BFD monitors a forwarding path but does not by itself create routing advertisements.

Explanation

Correct Answer

A:

The governing principle is: VRRP coordinates virtual default-gateway ownership among participating routers. In this scenario, the appropriate action is: Align VRRP group membership and select intended master priority and backup behavior. Valid evidence would show: Exactly one VRRP master owns the virtual gateway at a time under stable conditions.

Incorrect Answers

B:

“VRRP priority and preemption behavior are separate configured failover choices” responds to another technical or business failure: A maintenance engineer expects a higher-priority VRRP router to take back Master instantly although preemption is disabled. That source case depends on: VRRP priority and preemption behavior are separate configured failover choices. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “VRRP coordinates virtual default-gateway ownership among participating routers” because VRRP coordinates virtual default-gateway ownership among participating routers.

C:

“Virtual gateway addressing and neighbor-cache convergence influence failover traffic” responds to another technical or business failure: Two edge routers use independent VRRP groups with conflicting virtual MAC expectations and clients intermittently lose connectivity. That source case depends on: Virtual gateway addressing and neighbor-cache convergence influence failover traffic. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “VRRP coordinates virtual default-gateway ownership among participating routers” because VRRP coordinates virtual default-gateway ownership among participating routers.

D:

“BFD monitors a forwarding path but does not by itself create routing advertisements” responds to another technical or business failure: A BFD session is Up but a technician assumes that means every destination route through the neighbor is installed. That source case depends on: BFD monitors a forwarding path but does not by itself create routing advertisements. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “VRRP coordinates virtual default-gateway ownership among participating routers” because VRRP coordinates virtual default-gateway ownership among participating routers.

Question 674

At fictional Elmstone Transit, a network engineer supporting operations terminals is reviewing VRRP, BFD and redundancy design during a planned network scaling change (HCIP-H12-821-RELIABILITY-169). The observed network issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. Which next engineering action best addresses the reported problem?

  1. Identify shared physical dependencies and add independent power or placement where feasible.
  2. Configure suitable upstream route tracking and investigate WAN reachability beyond the LAN gateway.
  3. Review BFD session negotiation parameters and protocol association at both ends.
  4. Align VRRP group membership and select intended master priority and backup behavior.

Explanation

Correct Answer

D:

The directly responsive action is: Align VRRP group membership and select intended master priority and backup behavior. The specific reported fault is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. Confirmation should show: Exactly one VRRP master owns the virtual gateway at a time under stable conditions. The supporting technical principle is: VRRP coordinates virtual default-gateway ownership among participating routers.

Incorrect Answers

A:

“Identify shared physical dependencies and add independent power or placement where feasible” responds to another technical or business failure: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. That source case depends on: Network reliability depends on eliminating shared risks, not only duplicating network devices. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “Align VRRP group membership and select intended master priority and backup behavior” because VRRP coordinates virtual default-gateway ownership among participating routers.

B:

“Configure suitable upstream route tracking and investigate WAN reachability beyond the LAN gateway” responds to another technical or business failure: A VRRP virtual IP responds locally but remote services fail because both gateway uplinks have lost their default route. That source case depends on: Gateway availability and end-to-end network reachability are different reliability properties. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “Align VRRP group membership and select intended master priority and backup behavior” because VRRP coordinates virtual default-gateway ownership among participating routers.

C:

“Review BFD session negotiation parameters and protocol association at both ends” responds to another technical or business failure: BFD keeps an OSPF neighbor Down even after link restoration because the negotiated intervals or detection multiplier are incompatible. That source case depends on: BFD detection speed depends on compatible transmit and receive timers and multiplier behavior. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “Align VRRP group membership and select intended master priority and backup behavior” because VRRP coordinates virtual default-gateway ownership among participating routers.

Question 675

At fictional Elmstone Transit, a network engineer supporting operations terminals is reviewing VRRP, BFD and redundancy design during a planned network scaling change (HCIP-H12-821-RELIABILITY-169). The observed network issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. Which observation most directly verifies that the corrective change succeeded?

  1. Gateway mastership remains stable through normal transients and changes on genuine failure.
  2. Failure detection meets the service objective without spurious adjacency resets.
  3. Controlled loss of one supply feed preserves the defined critical forwarding service.
  4. Exactly one VRRP master owns the virtual gateway at a time under stable conditions.

Explanation

Correct Answer

D:

The best verification observation is: Exactly one VRRP master owns the virtual gateway at a time under stable conditions. It demonstrates the corrective action: Align VRRP group membership and select intended master priority and backup behavior. This fits the principle: VRRP coordinates virtual default-gateway ownership among participating routers. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Gateway mastership remains stable through normal transients and changes on genuine failure” responds to another technical or business failure: A VRRP group flaps repeatedly because upstream connectivity causes tracked priority to alternate around the peer threshold. That source case depends on: The best verification observation is: Gateway mastership remains stable through normal transients and changes on genuine failure. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “Exactly one VRRP master owns the virtual gateway at a time under stable conditions” because the best verification observation is: Exactly one VRRP master owns the virtual gateway at a time under stable conditions.

B:

“Failure detection meets the service objective without spurious adjacency resets” responds to another technical or business failure: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. That source case depends on: The best verification observation is: Failure detection meets the service objective without spurious adjacency resets. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “Exactly one VRRP master owns the virtual gateway at a time under stable conditions” because the best verification observation is: Exactly one VRRP master owns the virtual gateway at a time under stable conditions.

C:

“Controlled loss of one supply feed preserves the defined critical forwarding service” responds to another technical or business failure: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. That source case depends on: The best verification observation is: Controlled loss of one supply feed preserves the defined critical forwarding service. The present issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more direct action is “Exactly one VRRP master owns the virtual gateway at a time under stable conditions” because the best verification observation is: Exactly one VRRP master owns the virtual gateway at a time under stable conditions.

Question 676

At fictional Elmstone Transit, a network engineer supporting operations terminals is reviewing VRRP, BFD and redundancy design during a planned network scaling change (HCIP-H12-821-RELIABILITY-169). The observed network issue is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. Which ongoing preventive or detective control would best reduce recurrence?

  1. Include remote service probes in VRRP gateway validation.
  2. Test VRRP master and backup roles during campus change acceptance.
  3. Check both BFD and route installation in availability acceptance.
  4. Compare configured and negotiated BFD timers during network changes.

Explanation

Correct Answer

B:

The preventive or detective safeguard is: Test VRRP master and backup roles during campus change acceptance. This directly addresses the recurring fault: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The corrective action would be: Align VRRP group membership and select intended master priority and backup behavior. Success is demonstrated when: Exactly one VRRP master owns the virtual gateway at a time under stable conditions.

Incorrect Answers

A:

“Include remote service probes in VRRP gateway validation” addresses recurrence of another problem: A VRRP virtual IP responds locally but remote services fail because both gateway uplinks have lost their default route. That problem depends on: The preventive or detective safeguard is: Include remote service probes in VRRP gateway validation. The recurring risk here is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more targeted safeguard is “Test VRRP master and backup roles during campus change acceptance” because the preventive or detective safeguard is: Test VRRP master and backup roles during campus change acceptance.

C:

“Check both BFD and route installation in availability acceptance” addresses recurrence of another problem: A BFD session is Up but a technician assumes that means every destination route through the neighbor is installed. That problem depends on: The preventive or detective safeguard is: Check both BFD and route installation in availability acceptance. The recurring risk here is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more targeted safeguard is “Test VRRP master and backup roles during campus change acceptance” because the preventive or detective safeguard is: Test VRRP master and backup roles during campus change acceptance.

D:

“Compare configured and negotiated BFD timers during network changes” addresses recurrence of another problem: BFD keeps an OSPF neighbor Down even after link restoration because the negotiated intervals or detection multiplier are incompatible. That problem depends on: The preventive or detective safeguard is: Compare configured and negotiated BFD timers during network changes. The recurring risk here is: Two redundant gateways share a user VLAN but both are configured as active with the same VRRP virtual address and inconsistent group settings. The more targeted safeguard is “Test VRRP master and backup roles during campus change acceptance” because the preventive or detective safeguard is: Test VRRP master and backup roles during campus change acceptance.

Question 677

At fictional Pinewell Electronics, a network engineer supporting engineering labs is reviewing RSTP, MSTP and switching interconnects during a controlled failover exercise (HCIP-H12-821-SWITCH-170). The observed network issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. Which ongoing preventive or detective control would best reduce recurrence?

  1. Check spanning-tree topology and loop guards before adding dual uplinks.
  2. Test VLAN loop avoidance and default gateway failover separately.
  3. Audit edge-port classification and BPDU protection after topology changes.
  4. Run region consistency checks after any VLAN migration.

Explanation

Correct Answer

D:

The preventive or detective safeguard is: Run region consistency checks after any VLAN migration. This directly addresses the recurring fault: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The corrective action would be: Align region name, revision level and VLAN-instance mappings across the intended domain. Success is demonstrated when: MST configuration digests agree and switches join the intended common region.

Incorrect Answers

A:

“Check spanning-tree topology and loop guards before adding dual uplinks” addresses recurrence of another problem: An Ethernet campus has a physical loop but engineers disable spanning tree to reduce convergence delay. That problem depends on: The preventive or detective safeguard is: Check spanning-tree topology and loop guards before adding dual uplinks. The recurring risk here is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more targeted safeguard is “Run region consistency checks after any VLAN migration” because the preventive or detective safeguard is: Run region consistency checks after any VLAN migration.

B:

“Test VLAN loop avoidance and default gateway failover separately” addresses recurrence of another problem: A team expects MSTP instance root selection to affect layer-3 inter-VLAN gateway ownership automatically. That problem depends on: The preventive or detective safeguard is: Test VLAN loop avoidance and default gateway failover separately. The recurring risk here is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more targeted safeguard is “Run region consistency checks after any VLAN migration” because the preventive or detective safeguard is: Run region consistency checks after any VLAN migration.

C:

“Audit edge-port classification and BPDU protection after topology changes” addresses recurrence of another problem: An engineer places an edge-port setting on a trunk toward another switch and an unexpected BPDU enters the network. That problem depends on: The preventive or detective safeguard is: Audit edge-port classification and BPDU protection after topology changes. The recurring risk here is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more targeted safeguard is “Run region consistency checks after any VLAN migration” because the preventive or detective safeguard is: Run region consistency checks after any VLAN migration.

Question 678

At fictional Pinewell Electronics, a network engineer supporting engineering labs is reviewing RSTP, MSTP and switching interconnects during a controlled failover exercise (HCIP-H12-821-SWITCH-170). The observed network issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. Which routing, switching, or network principle best explains the appropriate solution?

  1. Spanning tree and default-gateway failover are independent control mechanisms.
  2. MST region membership depends on a consistent configuration digest, not merely a label.
  3. Spanning-tree selected paths depend on cumulative root cost and bridge identifiers.
  4. STP root election uses bridge identifier priorities and MAC tie-breaking.

Explanation

Correct Answer

B:

The governing principle is: MST region membership depends on a consistent configuration digest, not merely a label. In this scenario, the appropriate action is: Align region name, revision level and VLAN-instance mappings across the intended domain. Valid evidence would show: MST configuration digests agree and switches join the intended common region.

Incorrect Answers

A:

“Spanning tree and default-gateway failover are independent control mechanisms” responds to another technical or business failure: A team expects MSTP instance root selection to affect layer-3 inter-VLAN gateway ownership automatically. That source case depends on: Spanning tree and default-gateway failover are independent control mechanisms. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “MST region membership depends on a consistent configuration digest, not merely a label” because MST region membership depends on a consistent configuration digest, not merely a label.

C:

“Spanning-tree selected paths depend on cumulative root cost and bridge identifiers” responds to another technical or business failure: A switch link that should be an MST root port instead alternates forwarding because path costs differ from the planned design. That source case depends on: Spanning-tree selected paths depend on cumulative root cost and bridge identifiers. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “MST region membership depends on a consistent configuration digest, not merely a label” because MST region membership depends on a consistent configuration digest, not merely a label.

D:

“STP root election uses bridge identifier priorities and MAC tie-breaking” responds to another technical or business failure: Two switches disagree about the RSTP root bridge and forwarding follows a low-capacity distribution switch. That source case depends on: STP root election uses bridge identifier priorities and MAC tie-breaking. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “MST region membership depends on a consistent configuration digest, not merely a label” because MST region membership depends on a consistent configuration digest, not merely a label.

Question 679

At fictional Pinewell Electronics, a network engineer supporting engineering labs is reviewing RSTP, MSTP and switching interconnects during a controlled failover exercise (HCIP-H12-821-SWITCH-170). The observed network issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. Which observation most directly verifies that the corrective change succeeded?

  1. Both members appear in one stable logical stack with correct master and standby roles.
  2. MAC learning stabilizes and aggregated uplinks provide the intended redundancy.
  3. Selected VLANs follow their designated MST instance root and forwarding path.
  4. MST configuration digests agree and switches join the intended common region.

Explanation

Correct Answer

D:

The best verification observation is: MST configuration digests agree and switches join the intended common region. It demonstrates the corrective action: Align region name, revision level and VLAN-instance mappings across the intended domain. This fits the principle: MST region membership depends on a consistent configuration digest, not merely a label. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Both members appear in one stable logical stack with correct master and standby roles” responds to another technical or business failure: Two switches are configured for stacking but fail to form one logical unit due to incompatible member identifiers. That source case depends on: The best verification observation is: Both members appear in one stable logical stack with correct master and standby roles. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “MST configuration digests agree and switches join the intended common region” because the best verification observation is: MST configuration digests agree and switches join the intended common region.

B:

“MAC learning stabilizes and aggregated uplinks provide the intended redundancy” responds to another technical or business failure: A downstream aggregation switch sees duplicate MAC flaps after a switch cluster is formed without consistent cross-device link aggregation. That source case depends on: The best verification observation is: MAC learning stabilizes and aggregated uplinks provide the intended redundancy. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “MST configuration digests agree and switches join the intended common region” because the best verification observation is: MST configuration digests agree and switches join the intended common region.

C:

“Selected VLANs follow their designated MST instance root and forwarding path” responds to another technical or business failure: A network requires multiple spanning-tree topologies but maps all VLANs into one MST instance. That source case depends on: The best verification observation is: Selected VLANs follow their designated MST instance root and forwarding path. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “MST configuration digests agree and switches join the intended common region” because the best verification observation is: MST configuration digests agree and switches join the intended common region.

Question 680

At fictional Pinewell Electronics, a network engineer supporting engineering labs is reviewing RSTP, MSTP and switching interconnects during a controlled failover exercise (HCIP-H12-821-SWITCH-170). The observed network issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. Which next engineering action best addresses the reported problem?

  1. Permit the intended tagged VLAN on both sides of the trunk without broadening unrelated VLAN access.
  2. Remove inappropriate edge-port assumptions and enforce supported BPDU protection policy.
  3. Correct interface PVID or VLAN membership and validate separation with source MAC observations.
  4. Align region name, revision level and VLAN-instance mappings across the intended domain.

Explanation

Correct Answer

D:

The directly responsive action is: Align region name, revision level and VLAN-instance mappings across the intended domain. The specific reported fault is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. Confirmation should show: MST configuration digests agree and switches join the intended common region. The supporting technical principle is: MST region membership depends on a consistent configuration digest, not merely a label.

Incorrect Answers

A:

“Permit the intended tagged VLAN on both sides of the trunk without broadening unrelated VLAN access” responds to another technical or business failure: A technician adds a new VLAN but leaves it out of the allowed trunk list between access and aggregation switches. That source case depends on: VLAN trunking requires explicit compatible tagging and allowed membership. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “Align region name, revision level and VLAN-instance mappings across the intended domain” because MST region membership depends on a consistent configuration digest, not merely a label.

B:

“Remove inappropriate edge-port assumptions and enforce supported BPDU protection policy” responds to another technical or business failure: An engineer places an edge-port setting on a trunk toward another switch and an unexpected BPDU enters the network. That source case depends on: Edge-port optimizations are intended for endpoint-facing links rather than switch-to-switch trunks. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “Align region name, revision level and VLAN-instance mappings across the intended domain” because MST region membership depends on a consistent configuration digest, not merely a label.

C:

“Correct interface PVID or VLAN membership and validate separation with source MAC observations” responds to another technical or business failure: Users from two access VLANs unexpectedly communicate at layer 2 because the same port VLAN was configured on both groups. That source case depends on: A switch forwarding domain is determined by VLAN tagging and port membership. The present issue is: MSTP neighbors appear in different regions despite using the same region name because their VLAN mappings differ. The more direct action is “Align region name, revision level and VLAN-instance mappings across the intended domain” because MST region membership depends on a consistent configuration digest, not merely a label.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests