McAfee Secure

Exam Code: NSE5_FSW_AD-7.6

Exam Name: Fortinet NSE 5 - FortiSwitch 7.6 Administrator

Certification Provider: Fortinet

Corresponding Certification: NSE5

Fortinet NSE5_FSW_AD-7.6 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

64 Questions & Answers with Testing Engine

"Fortinet NSE 5 - FortiSwitch 7.6 Administrator Exam", also known as NSE5_FSW_AD-7.6 exam, is a Fortinet certification exam.

Pass your tests with the always up-to-date NSE5_FSW_AD-7.6 Exam Engine. Your NSE5_FSW_AD-7.6 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Fortinet NSE5_FSW_AD-7.6 Practice Test 17

Question 160

At the Maplehaven data network services firm, two managed FortiSwitch units must communicate across a transparent bridge that does not pass ordinary LLDP frames. Which setting or practice should be reviewed in future?

  1. Document the control and failure domains of each stack member
  2. Audit DSCP trust rules when access device roles change
  3. Validate edge-port designation whenever a port role changes
  4. Review FortiLink point-to-point settings when intermediate transport changes

Explanation

Correct Answer

D:

For the Maplehaven data network services firm, this maintenance action preserves the fix: review FortiLink point-to-point settings when intermediate transport changes. It should be revisited as the workload evolves.

Incorrect Answers

A:

Document the control and failure domains of each stack member is not the primary recurring safeguard for this problem. The team should review FortiLink point-to-point settings when intermediate transport changes. For the Maplehaven data network services firm, the direct corrective action is to use supported FortiLink point-to-point bridging settings on each relevant inter-switch port.

B:

Audit DSCP trust rules when access device roles change. That safeguard would help prevent recurrence of: Accepting arbitrary endpoint DSCP values lets a low-priority source consume priority queues. The risk being reviewed here is instead: A transparent intermediate device may not forward the control frames needed for normal FortiLink neighbor discovery. The matching ongoing control is: Review FortiLink point-to-point settings when intermediate transport changes.

C:

The suggested preventive check is: Validate edge-port designation whenever a port role changes. Its technical scope concerns: A non-edge STP transition may delay client connectivity even when no downstream bridge exists. This question asks how to sustain control over: A transparent intermediate device may not forward the control frames needed for normal FortiLink neighbor discovery. The more targeted safeguard is: Review FortiLink point-to-point settings when intermediate transport changes.

Question 161

At the Willowford regional network integrator, a workstation moves access ports but traffic continues to forward to the old port temporarily. Which corrective action best meets the requirement?

  1. Inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly
  2. Inspect the supported routing table and route precedence before changing link configuration
  3. Restore the supported uplink membership that carries all approved service VLANs
  4. Restore supported STP or a valid aggregated topology instead of creating unrestricted redundant Layer 2 paths

Explanation

Correct Answer

A:

This is the direct FortiSwitch 7.6 administration remedy: inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly. The observed risk is that layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN; a passing acceptance check would show that the endpoint MAC appears on the new port and frames arrive at the new location.

Incorrect Answers

B:

The offered action is: Inspect the supported routing table and route precedence before changing link configuration. It is associated with this separate technical condition: Configured intent may not match the route actually selected for forwarding. The actual incident concerns a different dependency: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. The corresponding change is: Inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly.

C:

Restore the supported uplink membership that carries all approved service VLANs can be useful for another FortiSwitch 7.6 administration workflow, but it leaves the immediate failure unresolved. Here the priority is to inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly. For the Willowford regional network integrator, the direct corrective action is to inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly.

D:

The offered alternative is: Restore supported STP or a valid aggregated topology instead of creating unrestricted redundant Layer 2 paths. It addresses this separate failure mode: Parallel unmanaged forwarding paths can cause persistent Ethernet loops. In the current case, the observed mechanism is: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. The keyed action, Inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly., targets that condition more directly.

Question 162

At the Willowford regional network integrator, a workstation moves access ports but traffic continues to forward to the old port temporarily. Which underlying issue most directly explains this situation?

  1. Without valid membership tracking multicast may be flooded to non-subscribers
  2. An intermediary can block discovery advertisements even when Ethernet connectivity works
  3. Inconsistent advertised application policies can cause mismatched VLAN or QoS markings
  4. Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN

Explanation

Correct Answer

D:

The problem stems from the fact that layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. A correct solution would inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly and check that the endpoint MAC appears on the new port and frames arrive at the new location.

Incorrect Answers

A:

The offered principle is: Without valid membership tracking multicast may be flooded to non-subscribers. In the source material it is associated with: Without valid membership tracking multicast may be flooded to non-subscribers. This case has a different controlling cause: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. Its keyed mechanism is: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN.

B:

An intermediary can block discovery advertisements even when Ethernet connectivity works. That is not the mechanism that accounts for the stated failure at the Willowford regional network integrator.

C:

The offered principle is: Inconsistent advertised application policies can cause mismatched VLAN or QoS markings. In the source material it is associated with: Inconsistent advertised application policies can cause mismatched VLAN or QoS markings. This case has a different controlling cause: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. Its keyed mechanism is: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN.

Question 163

At the Willowford regional network integrator, a workstation moves access ports but traffic continues to forward to the old port temporarily. What evidence would justify considering this concern addressed?

  1. Multiple independent test flows use expected available next hops without reordering
  2. A staged ring test retains switch management and does not form a loop
  3. The ISL stays stable with valid optical diagnostics and every member remains managed
  4. The endpoint MAC appears on the new port and frames arrive at the new location

Explanation

Correct Answer

D:

This is the relevant acceptance result: the endpoint MAC appears on the new port and frames arrive at the new location. It demonstrates the outcome of choosing to inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly.

Incorrect Answers

A:

Multiple independent test flows use expected available next hops without reordering. That result would test a control for this other failure: Equal-cost multipath may use a flow hash rather than distributing consecutive packets across every path. The question instead requires evidence for: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. The direct outcome to verify is: The endpoint MAC appears on the new port and frames arrive at the new location.

B:

The offered observation is: A staged ring test retains switch management and does not form a loop. It would support the separate mechanism: A managed FortiLink topology has control and data requirements beyond ordinary standalone edge switch assumptions. In this case the decisive dependency is: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. The original keyed verification is: The endpoint MAC appears on the new port and frames arrive at the new location.

C:

The ISL stays stable with valid optical diagnostics and every member remains managed. That result would test a control for this other failure: Optical incompatibility can break discovery and data connectivity regardless of VLAN configuration. The question instead requires evidence for: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. The direct outcome to verify is: The endpoint MAC appears on the new port and frames arrive at the new location.

Question 164

At the Willowford regional network integrator, a workstation moves access ports but traffic continues to forward to the old port temporarily. How should the organization sustain the improvement?

  1. Track path health and ECMP consistency during link upgrades
  2. Track MAC movement alerts after large office rearrangements
  3. Recheck port speed after transceiver replacements
  4. Validate edge-port designation whenever a port role changes

Explanation

Correct Answer

B:

For the Willowford regional network integrator, this maintenance action preserves the fix: track MAC movement alerts after large office rearrangements. It should be revisited as the workload evolves.

Incorrect Answers

A:

The suggested preventive check is: Track path health and ECMP consistency during link upgrades. Its technical scope concerns: Equal-cost multipath may use a flow hash rather than distributing consecutive packets across every path. This question asks how to sustain control over: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. The more targeted safeguard is: Track MAC movement alerts after large office rearrangements.

C:

That routine supports port speed mismatch, but the relevant ongoing risk requires the team to track MAC movement alerts after large office rearrangements. For the Willowford regional network integrator, the direct corrective action is to inspect learned MAC location and correct the port VLAN or aging condition rather than changing IP routes blindly.

D:

Validate edge-port designation whenever a port role changes. That safeguard would help prevent recurrence of: A non-edge STP transition may delay client connectivity even when no downstream bridge exists. The risk being reviewed here is instead: Layer 2 forwarding depends on current MAC-to-port learning within the correct VLAN. The matching ongoing control is: Track MAC movement alerts after large office rearrangements.

Question 165

At the Pinewick multisite IT support team, a switch floods unknown unicast unusually often after a new large virtual-host deployment. Which approach best resolves the described issue?

  1. Configure supported multicast routing in the appropriate Layer 3 design in addition to receiver membership controls
  2. Use the Fortinet supported aggregate and LACP setting for the chosen FortiLink topology
  3. Check supported MAC table capacity and learning patterns before resizing or segmenting the design
  4. Enable supported storm control on the affected access edge with appropriate thresholds

Explanation

Correct Answer

C:

This solution addresses the stated limitation: excessive unique source addresses may strain hardware learning resources. Implementing it means the team should check supported MAC table capacity and learning patterns before resizing or segmenting the design, then verify that observed learned-address counts remain within supported limits and flooding falls.

Incorrect Answers

A:

Configure supported multicast routing in the appropriate Layer 3 design in addition to receiver membership controls can be useful for another FortiSwitch 7.6 administration workflow, but it leaves the immediate failure unresolved. Here the priority is to check supported MAC table capacity and learning patterns before resizing or segmenting the design. For the Pinewick multisite IT support team, the direct corrective action is to check supported MAC table capacity and learning patterns before resizing or segmenting the design.

B:

The offered action is: Use the Fortinet supported aggregate and LACP setting for the chosen FortiLink topology. It is associated with this separate technical condition: FortiLink aggregate requirements are topology-specific and ordinary client LAG assumptions may not apply. The actual incident concerns a different dependency: Excessive unique source addresses may strain hardware learning resources. The corresponding change is: Check supported MAC table capacity and learning patterns before resizing or segmenting the design.

D:

Enable supported storm control on the affected access edge with appropriate thresholds addresses a different kind of problem: excess broadcasts can consume shared switching bandwidth and CPU resources. Here the reported weakness is that excessive unique source addresses may strain hardware learning resources. For the Pinewick multisite IT support team, the direct corrective action is to check supported MAC table capacity and learning patterns before resizing or segmenting the design.

Question 166

At the Pinewick multisite IT support team, a switch floods unknown unicast unusually often after a new large virtual-host deployment. Which explanation best accounts for the concern?

  1. Local bypass routing can defeat the approved security inspection architecture
  2. STP chooses paths from bridge and port metrics rather than business labels
  3. A non-edge STP transition may delay client connectivity even when no downstream bridge exists
  4. Excessive unique source addresses may strain hardware learning resources

Explanation

Correct Answer

D:

This identifies the root issue: excessive unique source addresses may strain hardware learning resources. At the Pinewick multisite IT support team, the team should therefore check supported MAC table capacity and learning patterns before resizing or segmenting the design.

Incorrect Answers

A:

The offered principle is: Local bypass routing can defeat the approved security inspection architecture. In the source material it is associated with: Local bypass routing can defeat the approved security inspection architecture. This case has a different controlling cause: Excessive unique source addresses may strain hardware learning resources. Its keyed mechanism is: Excessive unique source addresses may strain hardware learning resources.

B:

Although sTP chooses paths from bridge and port metrics rather than business labels, the presented symptoms do not support that as the primary cause; they indicate that excessive unique source addresses may strain hardware learning resources. For the Pinewick multisite IT support team, the direct corrective action is to check supported MAC table capacity and learning patterns before resizing or segmenting the design.

C:

The offered principle is: A non-edge STP transition may delay client connectivity even when no downstream bridge exists. In the source material it is associated with: A non-edge STP transition may delay client connectivity even when no downstream bridge exists. This case has a different controlling cause: Excessive unique source addresses may strain hardware learning resources. Its keyed mechanism is: Excessive unique source addresses may strain hardware learning resources.

Question 167

At the Pinewick multisite IT support team, a switch floods unknown unicast unusually often after a new large virtual-host deployment. Which test result best shows the requirement is met?

  1. A route lookup chooses the approved path and a controlled failover selects backup
  2. Observed LLDP chassis and port identifiers match the verified cable map
  3. Observed learned-address counts remain within supported limits and flooding falls
  4. A test phone discovers the voice VLAN and obtains its voice network address

Explanation

Correct Answer

C:

Because excessive unique source addresses may strain hardware learning resources, the required evidence must show that observed learned-address counts remain within supported limits and flooding falls. A healthy endpoint status alone is insufficient.

Incorrect Answers

A:

A route lookup chooses the approved path and a controlled failover selects backup. That result would test a control for this other failure: Configured intent may not match the route actually selected for forwarding. The question instead requires evidence for: Excessive unique source addresses may strain hardware learning resources. The direct outcome to verify is: Observed learned-address counts remain within supported limits and flooding falls.

B:

The offered observation is: Observed LLDP chassis and port identifiers match the verified cable map. It would support the separate mechanism: Port labels may become stale when cables move and must be reconciled with observed neighbors. In this case the decisive dependency is: Excessive unique source addresses may strain hardware learning resources. The original keyed verification is: Observed learned-address counts remain within supported limits and flooding falls.

D:

At the Pinewick multisite IT support team, a result about voice lldp-med discovery would not show that the team corrected the failure where excessive unique source addresses may strain hardware learning resources.

Question 168

At the Pinewick multisite IT support team, a switch floods unknown unicast unusually often after a new large virtual-host deployment. Which ongoing control best prevents this issue from recurring?

  1. Track MAC movement alerts after large office rearrangements
  2. Forecast MAC population from virtualized host growth
  3. Compare MSTP region digests when adding a new switch
  4. Maintain a port-role diagram for each managed FortiSwitch cluster

Explanation

Correct Answer

B:

The needed prevention is to forecast MAC population from virtualized host growth. It directly sustains the original change to check supported MAC table capacity and learning patterns before resizing or segmenting the design.

Incorrect Answers

A:

That routine supports mac address learning path, but the relevant ongoing risk requires the team to forecast MAC population from virtualized host growth. For the Pinewick multisite IT support team, the direct corrective action is to check supported MAC table capacity and learning patterns before resizing or segmenting the design.

C:

Compare MSTP region digests when adding a new switch is not the primary recurring safeguard for this problem. The team should forecast MAC population from virtualized host growth. For the Pinewick multisite IT support team, the direct corrective action is to check supported MAC table capacity and learning patterns before resizing or segmenting the design.

D:

Maintain a port-role diagram for each managed FortiSwitch cluster. That safeguard would help prevent recurrence of: A physical link on the wrong port role does not necessarily join the managed FortiSwitch topology. The risk being reviewed here is instead: Excessive unique source addresses may strain hardware learning resources. The matching ongoing control is: Forecast MAC population from virtualized host growth.

Question 169

At the Cedarport campus infrastructure group, two connected FortiSwitch units have differently configured LACP trunk keys and only one member forwards. Which implementation choice best addresses the situation?

  1. Set the correct trusted DHCP snooping boundary on the authorized server-facing port
  2. Verify supported STP compatibility at the region boundary and plan a loop-free topology
  3. Align aggregation mode partner settings and member characteristics on both switches
  4. Validate the FortiSwitch port role and supported ISL discovery or configured inter-switch trunk

Explanation

Correct Answer

C:

This is the direct FortiSwitch 7.6 administration remedy: align aggregation mode partner settings and member characteristics on both switches. The observed risk is that mismatched LACP negotiation can exclude ports from the intended logical trunk; a passing acceptance check would show that all planned member ports enter the active trunk and survive one-link loss.

Incorrect Answers

A:

This alternative would be suitable where dHCP snooping can filter legitimate server responses when the server path is not trusted. It does not by itself resolve the need to align aggregation mode partner settings and member characteristics on both switches. For the Cedarport campus infrastructure group, the direct corrective action is to align aggregation mode partner settings and member characteristics on both switches.

B:

Verify supported STP compatibility at the region boundary and plan a loop-free topology addresses a different kind of problem: different STP variants can interoperate at boundaries without sharing every internal instance decision. Here the reported weakness is that mismatched LACP negotiation can exclude ports from the intended logical trunk. For the Cedarport campus infrastructure group, the direct corrective action is to align aggregation mode partner settings and member characteristics on both switches.

D:

The offered alternative is: Validate the FortiSwitch port role and supported ISL discovery or configured inter-switch trunk. It addresses this separate failure mode: A downstream switch cannot be discovered if its inter-switch connection lacks the required FortiLink control path. In the current case, the observed mechanism is: Mismatched LACP negotiation can exclude ports from the intended logical trunk. The keyed action, Align aggregation mode partner settings and member characteristics on both switches., targets that condition more directly.

Question 170

At the Cedarport campus infrastructure group, two connected FortiSwitch units have differently configured LACP trunk keys and only one member forwards. What risk should the team identify as the primary issue?

  1. Without valid membership tracking multicast may be flooded to non-subscribers
  2. Mismatched LACP negotiation can exclude ports from the intended logical trunk
  3. Unrestricted low-priority demand can fill shared switch buffers during contention
  4. A transparent intermediate device may not forward the control frames needed for normal FortiLink neighbor discovery

Explanation

Correct Answer

B:

This identifies the root issue: mismatched LACP negotiation can exclude ports from the intended logical trunk. At the Cedarport campus infrastructure group, the team should therefore align aggregation mode partner settings and member characteristics on both switches.

Incorrect Answers

A:

The offered action is: Without valid membership tracking multicast may be flooded to non-subscribers. It is associated with this separate technical condition: Without valid membership tracking multicast may be flooded to non-subscribers. The actual incident concerns a different dependency: Mismatched LACP negotiation can exclude ports from the intended logical trunk. The corresponding change is: Mismatched LACP negotiation can exclude ports from the intended logical trunk.

C:

The offered alternative is: Unrestricted low-priority demand can fill shared switch buffers during contention. It addresses this separate failure mode: Unrestricted low-priority demand can fill shared switch buffers during contention. In the current case, the observed mechanism is: Mismatched LACP negotiation can exclude ports from the intended logical trunk. The keyed action, Mismatched LACP negotiation can exclude ports from the intended logical trunk., targets that condition more directly.

D:

A transparent intermediate device may not forward the control frames needed for normal FortiLink neighbor discovery. That is not the mechanism that accounts for the stated failure at the Cedarport campus infrastructure group.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests