McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 13

Question 120

At fictional Pinewell Electronics, a network engineer supporting engineering labs is reviewing VRRP, BFD and redundancy design during a lab-to-production acceptance (HCIP-H12-821-RELIABILITY-030). The observed network issue is: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. Which next engineering action best addresses the reported problem?

  1. Repair the underlying link and choose supported detection timers or BFD that match availability requirements.
  2. Configure suitable upstream route tracking and investigate WAN reachability beyond the LAN gateway.
  3. Redesign independent backup next-hop reachability and validate actual alternate path availability.
  4. Identify shared physical dependencies and add independent power or placement where feasible.

Explanation

Correct Answer

A:

The directly responsive action is: Repair the underlying link and choose supported detection timers or BFD that match availability requirements. The specific reported fault is: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. Confirmation should show: Failure detection meets the service objective without spurious adjacency resets. The supporting technical principle is: Reliability design balances false failures against convergence latency.

Incorrect Answers

B:

“Configure suitable upstream route tracking and investigate WAN reachability beyond the LAN gateway” responds to another technical or business failure: A VRRP virtual IP responds locally but remote services fail because both gateway uplinks have lost their default route. That source case depends on: Gateway availability and end-to-end network reachability are different reliability properties. The present issue is: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. The more direct action is “Repair the underlying link and choose supported detection timers or BFD that match availability requirements” because Reliability design balances false failures against convergence latency.

C:

“Redesign independent backup next-hop reachability and validate actual alternate path availability” responds to another technical or business failure: An interface failure is detected rapidly by BFD but the backup route points to the same failed upstream dependency. That source case depends on: Fast fault detection is ineffective without a genuinely independent recovery path. The present issue is: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. The more direct action is “Repair the underlying link and choose supported detection timers or BFD that match availability requirements” because Reliability design balances false failures against convergence latency.

D:

“Identify shared physical dependencies and add independent power or placement where feasible” responds to another technical or business failure: A campus design has redundant routers and switches but both power feeds terminate on one supply circuit. That source case depends on: Network reliability depends on eliminating shared risks, not only duplicating network devices. The present issue is: An operator increases routing protocol Dead timers to stabilize a flaky link but overlooks the resulting slow failover. The more direct action is “Repair the underlying link and choose supported detection timers or BFD that match availability requirements” because Reliability design balances false failures against convergence latency.

Question 121

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing OSPF area design and link-state convergence during an initial deployment test (HCIP-H12-821-OSPF-031). The observed network issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. Which routing, switching, or network principle best explains the appropriate solution?

  1. OSPF uses accumulated interface cost to select shortest paths within its topology.
  2. Explicit OSPF interface costs can control shortest-path metrics independent of interface speed.
  3. Route summarization reduces advertisements but can conceal specific reachability failures.
  4. OSPF external route next-hop selection can use the LSA forwarding address when present.

Explanation

Correct Answer

C:

The governing principle is: Route summarization reduces advertisements but can conceal specific reachability failures. In this scenario, the appropriate action is: Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design. Valid evidence would show: Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented.

Incorrect Answers

A:

“OSPF uses accumulated interface cost to select shortest paths within its topology” responds to another technical or business failure: An operator raises OSPF interface cost expecting every transit path to become more attractive. That source case depends on: OSPF uses accumulated interface cost to select shortest paths within its topology. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Route summarization reduces advertisements but can conceal specific reachability failures” because Route summarization reduces advertisements but can conceal specific reachability failures.

B:

“Explicit OSPF interface costs can control shortest-path metrics independent of interface speed” responds to another technical or business failure: A failover design sets interface bandwidth but ignores manually configured OSPF costs that override the intended metric. That source case depends on: Explicit OSPF interface costs can control shortest-path metrics independent of interface speed. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Route summarization reduces advertisements but can conceal specific reachability failures” because Route summarization reduces advertisements but can conceal specific reachability failures.

D:

“OSPF external route next-hop selection can use the LSA forwarding address when present” responds to another technical or business failure: An external OSPF route prefers the wrong exit because its forwarding address is unreachable or unexpected. That source case depends on: OSPF external route next-hop selection can use the LSA forwarding address when present. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Route summarization reduces advertisements but can conceal specific reachability failures” because Route summarization reduces advertisements but can conceal specific reachability failures.

Question 122

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing OSPF area design and link-state convergence during an initial deployment test (HCIP-H12-821-OSPF-031). The observed network issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. Which observation most directly verifies that the corrective change succeeded?

  1. Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented.
  2. Locally redistributed prefixes remain reachable while the defined external LSA constraints hold.
  3. The interfaces agree on area ID and reach the expected OSPF neighbor state.
  4. The neighbor remains stable beyond multiple Dead intervals under normal traffic.

Explanation

Correct Answer

A:

The best verification observation is: Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented. It demonstrates the corrective action: Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design. This fits the principle: Route summarization reduces advertisements but can conceal specific reachability failures. Verify on the actual Huawei platform and network release.

Incorrect Answers

B:

“Locally redistributed prefixes remain reachable while the defined external LSA constraints hold” responds to another technical or business failure: An engineer designates an OSPF NSSA as a stub to reduce LSAs but unintentionally removes local redistribution. That source case depends on: The best verification observation is: Locally redistributed prefixes remain reachable while the defined external LSA constraints hold. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented” because the best verification observation is: Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented.

C:

“The interfaces agree on area ID and reach the expected OSPF neighbor state” responds to another technical or business failure: Two neighboring Huawei routers exchange Hello packets but never become OSPF neighbors because their area identifiers differ. That source case depends on: The best verification observation is: The interfaces agree on area ID and reach the expected OSPF neighbor state. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented” because the best verification observation is: Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented.

D:

“The neighbor remains stable beyond multiple Dead intervals under normal traffic” responds to another technical or business failure: Routers have the same network prefix but one side uses a different OSPF Hello interval on an Ethernet segment. That source case depends on: The best verification observation is: The neighbor remains stable beyond multiple Dead intervals under normal traffic. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented” because the best verification observation is: Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented.

Question 123

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing OSPF area design and link-state convergence during an initial deployment test (HCIP-H12-821-OSPF-031). The observed network issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. Which ongoing preventive or detective control would best reduce recurrence?

  1. Validate current DR or BDR role rather than predicting it from priority alone.
  2. Validate each constituent prefix and failover behavior under a planned aggregate.
  3. Check duplicate router IDs in configuration reviews and fault diagnostics.
  4. Compare redistributed prefix lists and Type 5 presence in each permitted area.

Explanation

Correct Answer

B:

The preventive or detective safeguard is: Validate each constituent prefix and failover behavior under a planned aggregate. This directly addresses the recurring fault: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The corrective action would be: Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design. Success is demonstrated when: Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented.

Incorrect Answers

A:

“Validate current DR or BDR role rather than predicting it from priority alone” addresses recurrence of another problem: An OSPF DR election change unexpectedly disrupts traffic because an engineer assumes elections are always preemptive. That problem depends on: The preventive or detective safeguard is: Validate current DR or BDR role rather than predicting it from priority alone. The recurring risk here is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more targeted safeguard is “Validate each constituent prefix and failover behavior under a planned aggregate” because the preventive or detective safeguard is: Validate each constituent prefix and failover behavior under a planned aggregate.

C:

“Check duplicate router IDs in configuration reviews and fault diagnostics” addresses recurrence of another problem: OSPF neighbors become stuck in ExStart because both routers are configured with the same router ID. That problem depends on: The preventive or detective safeguard is: Check duplicate router IDs in configuration reviews and fault diagnostics. The recurring risk here is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more targeted safeguard is “Validate each constituent prefix and failover behavior under a planned aggregate” because the preventive or detective safeguard is: Validate each constituent prefix and failover behavior under a planned aggregate.

D:

“Compare redistributed prefix lists and Type 5 presence in each permitted area” addresses recurrence of another problem: An ASBR redistributes a static service subnet but other areas never see its external OSPF destination. That problem depends on: The preventive or detective safeguard is: Compare redistributed prefix lists and Type 5 presence in each permitted area. The recurring risk here is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more targeted safeguard is “Validate each constituent prefix and failover behavior under a planned aggregate” because the preventive or detective safeguard is: Validate each constituent prefix and failover behavior under a planned aggregate.

Question 124

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing OSPF area design and link-state convergence during an initial deployment test (HCIP-H12-821-OSPF-031). The observed network issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. Which next engineering action best addresses the reported problem?

  1. Inspect external redistribution configuration, LSA Type 5 generation and area restrictions.
  2. Check NSSA Type 7 origination and the ABR's permitted Type 7 to Type 5 translation.
  3. Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design.
  4. Review OSPF interface priorities and the existing DR or BDR roles before choosing a change.

Explanation

Correct Answer

C:

The directly responsive action is: Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design. The specific reported fault is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. Confirmation should show: Only intended reachable subnets are forwarded and aggregate black holes are documented or prevented. The supporting technical principle is: Route summarization reduces advertisements but can conceal specific reachability failures.

Incorrect Answers

A:

“Inspect external redistribution configuration, LSA Type 5 generation and area restrictions” responds to another technical or business failure: An ASBR redistributes a static service subnet but other areas never see its external OSPF destination. That source case depends on: OSPF external routing requires correctly originated and flooded AS-external LSAs. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design” because Route summarization reduces advertisements but can conceal specific reachability failures.

B:

“Check NSSA Type 7 origination and the ABR's permitted Type 7 to Type 5 translation” responds to another technical or business failure: An NSSA branch redistributes a local service prefix but the backbone never receives the route. That source case depends on: NSSA external routes use Type 7 LSAs internally and can be translated at an ABR. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design” because Route summarization reduces advertisements but can conceal specific reachability failures.

D:

“Review OSPF interface priorities and the existing DR or BDR roles before choosing a change” responds to another technical or business failure: A new router with OSPF priority zero fails to become the designated router even after repeated interface bounces. That source case depends on: OSPF interface priority zero makes a router ineligible to be elected DR or BDR. The present issue is: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. The more direct action is “Inspect ABR summarization ranges and ensure constituent routes and discard behavior match the design” because Route summarization reduces advertisements but can conceal specific reachability failures.

Question 125

At fictional Summit Agriculture, a network engineer supporting remote rural branches is reviewing IS-IS level-aware topology and database synchronization during a baseline compliance test (HCIP-H12-821-ISIS-032). The observed network issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. Which next engineering action best addresses the reported problem?

  1. Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy.
  2. Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability.
  3. Assign each IS-IS node a unique stable system identifier within the domain.
  4. Confirm the expected nearest Level 1/2 border route and associated default or leaking policy.

Explanation

Correct Answer

A:

The directly responsive action is: Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy. The specific reported fault is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. Confirmation should show: The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB. The supporting technical principle is: An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.

Incorrect Answers

B:

“Use supported IS-IS overload-bit maintenance procedures while preserving required local reachability” responds to another technical or business failure: A maintenance router still attracts IS-IS transit traffic after operators intend it to avoid forwarding. That source case depends on: IS-IS overload signaling can discourage use of a router as a transit node. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy” because an IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.

C:

“Assign each IS-IS node a unique stable system identifier within the domain” responds to another technical or business failure: An IS-IS configuration reuses one system ID on two distinct routers and link-state advertisements become ambiguous. That source case depends on: IS-IS identifies routing systems using unique system IDs. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy” because an IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.

D:

“Confirm the expected nearest Level 1/2 border route and associated default or leaking policy” responds to another technical or business failure: A Level 1-only router cannot reach an IP prefix advertised only outside its local IS-IS area. That source case depends on: IS-IS Level 1 routing has area-local visibility and relies on Level 2 interarea reachability. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy” because an IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.

Question 126

At fictional Summit Agriculture, a network engineer supporting remote rural branches is reviewing IS-IS level-aware topology and database synchronization during a baseline compliance test (HCIP-H12-821-ISIS-032). The observed network issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. Which routing, switching, or network principle best explains the appropriate solution?

  1. IS-IS route leaking trades specific interarea visibility against scaling and policy control.
  2. IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement.
  3. An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.
  4. IS-IS database consistency relies on link-state PDU sequencing and flooding acknowledgements.

Explanation

Correct Answer

C:

The governing principle is: An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised. In this scenario, the appropriate action is: Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy. Valid evidence would show: The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB.

Incorrect Answers

A:

“IS-IS route leaking trades specific interarea visibility against scaling and policy control” responds to another technical or business failure: An engineer leaks all Level 2 routes into Level 1 and overwhelms a branch routing table. That source case depends on: IS-IS route leaking trades specific interarea visibility against scaling and policy control. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised” because an IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.

B:

“IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement” responds to another technical or business failure: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. That source case depends on: IS-IS DIS elections are a broadcast-LAN behavior, not a point-to-point requirement. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised” because an IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.

D:

“IS-IS database consistency relies on link-state PDU sequencing and flooding acknowledgements” responds to another technical or business failure: An IS-IS area contains conflicting LSP versions after connectivity flaps and routers disagree about routes. That source case depends on: IS-IS database consistency relies on link-state PDU sequencing and flooding acknowledgements. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised” because an IS-IS neighbor relationship alone does not guarantee every network prefix is advertised.

Question 127

At fictional Summit Agriculture, a network engineer supporting remote rural branches is reviewing IS-IS level-aware topology and database synchronization during a baseline compliance test (HCIP-H12-821-ISIS-032). The observed network issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. Which observation most directly verifies that the corrective change succeeded?

  1. Only the intended reachable interarea prefixes appear in the Level 1 database.
  2. Neighbor databases show distinct system IDs and consistent LSP origins.
  3. Access routers select the documented exit and no longer follow an accidental preferred attachment.
  4. The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB.

Explanation

Correct Answer

D:

The best verification observation is: The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB. It demonstrates the corrective action: Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy. This fits the principle: An IS-IS neighbor relationship alone does not guarantee every network prefix is advertised. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Only the intended reachable interarea prefixes appear in the Level 1 database” responds to another technical or business failure: An engineer leaks all Level 2 routes into Level 1 and overwhelms a branch routing table. That source case depends on: The best verification observation is: Only the intended reachable interarea prefixes appear in the Level 1 database. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB” because the best verification observation is: The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB.

B:

“Neighbor databases show distinct system IDs and consistent LSP origins” responds to another technical or business failure: An IS-IS configuration reuses one system ID on two distinct routers and link-state advertisements become ambiguous. That source case depends on: The best verification observation is: Neighbor databases show distinct system IDs and consistent LSP origins. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB” because the best verification observation is: The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB.

C:

“Access routers select the documented exit and no longer follow an accidental preferred attachment” responds to another technical or business failure: An IS-IS Level 1 router gets an unwanted default path after an L1/L2 node reports reachability to other areas. That source case depends on: The best verification observation is: Access routers select the documented exit and no longer follow an accidental preferred attachment. The present issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more direct action is “The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB” because the best verification observation is: The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB.

Question 128

At fictional Summit Agriculture, a network engineer supporting remote rural branches is reviewing IS-IS level-aware topology and database synchronization during a baseline compliance test (HCIP-H12-821-ISIS-032). The observed network issue is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. Which ongoing preventive or detective control would best reduce recurrence?

  1. Verify reachability TLVs and routing policy after interface activation.
  2. Label protocol-specific LAN election roles in troubleshooting diagrams.
  3. Include actual circuit topology and type in ISIS troubleshooting checks.
  4. Compare circuit-type values during core link acceptance.

Explanation

Correct Answer

A:

The preventive or detective safeguard is: Verify reachability TLVs and routing policy after interface activation. This directly addresses the recurring fault: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The corrective action would be: Check whether IPv4 reachability is advertised under the correct IS-IS topology and filtered by policy. Success is demonstrated when: The required IPv4 prefix appears through the intended IS-IS route in the RIB and FIB.

Incorrect Answers

B:

“Label protocol-specific LAN election roles in troubleshooting diagrams” addresses recurrence of another problem: An IS-IS router is elected designated intermediate system on an Ethernet segment but an engineer calls it an OSPF DR. That problem depends on: The preventive or detective safeguard is: Label protocol-specific LAN election roles in troubleshooting diagrams. The recurring risk here is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more targeted safeguard is “Verify reachability TLVs and routing policy after interface activation” because the preventive or detective safeguard is: Verify reachability TLVs and routing policy after interface activation.

C:

“Include actual circuit topology and type in ISIS troubleshooting checks” addresses recurrence of another problem: An engineer expects every IS-IS point-to-point interface to elect a LAN designated intermediate system. That problem depends on: The preventive or detective safeguard is: Include actual circuit topology and type in ISIS troubleshooting checks. The recurring risk here is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more targeted safeguard is “Verify reachability TLVs and routing policy after interface activation” because the preventive or detective safeguard is: Verify reachability TLVs and routing policy after interface activation.

D:

“Compare circuit-type values during core link acceptance” addresses recurrence of another problem: Two Level 2 IS-IS routers do not form neighbors because one interface is configured for Level 1-only adjacencies. That problem depends on: The preventive or detective safeguard is: Compare circuit-type values during core link acceptance. The recurring risk here is: An IS-IS neighbor forms correctly but the expected IPv4 destination never appears in downstream route tables. The more targeted safeguard is “Verify reachability TLVs and routing policy after interface activation” because the preventive or detective safeguard is: Verify reachability TLVs and routing policy after interface activation.

Question 129

At fictional Lakeshore Finance, a network engineer supporting transaction systems is reviewing route-policy and traffic-control behavior during a lab-to-production acceptance (HCIP-H12-821-POLICY-033). The observed network issue is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. Which observation most directly verifies that the corrective change succeeded?

  1. Packets retain intended service classification through each trusted hop.
  2. The intended service flow changes next hop while other routes retain established egress.
  3. Traffic tests confirm the authorized request and response directions are treated as designed.
  4. Every planned source group uses its assigned path with no unintended routing side effects.

Explanation

Correct Answer

D:

The best verification observation is: Every planned source group uses its assigned path with no unintended routing side effects. It demonstrates the corrective action: Generate probes from each intended source address or VLAN and observe policy match statistics. This fits the principle: Source-sensitive forwarding policy cannot be verified using only destination-based generic probes. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Packets retain intended service classification through each trusted hop” responds to another technical or business failure: A QoS policy marks packets DSCP but a downstream switch strips or overwrites those markings. That source case depends on: The best verification observation is: Packets retain intended service classification through each trusted hop. The present issue is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. The more direct action is “Every planned source group uses its assigned path with no unintended routing side effects” because the best verification observation is: Every planned source group uses its assigned path with no unintended routing side effects.

B:

“The intended service flow changes next hop while other routes retain established egress” responds to another technical or business failure: A dual-provider network expects a routing preference change to affect only one VLAN yet every route in the VRF changes. That source case depends on: The best verification observation is: The intended service flow changes next hop while other routes retain established egress. The present issue is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. The more direct action is “Every planned source group uses its assigned path with no unintended routing side effects” because the best verification observation is: Every planned source group uses its assigned path with no unintended routing side effects.

C:

“Traffic tests confirm the authorized request and response directions are treated as designed” responds to another technical or business failure: An ACL only denies one direction of a TCP conversation and the security team assumes return packets are automatically blocked. That source case depends on: The best verification observation is: Traffic tests confirm the authorized request and response directions are treated as designed. The present issue is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. The more direct action is “Every planned source group uses its assigned path with no unintended routing side effects” because the best verification observation is: Every planned source group uses its assigned path with no unintended routing side effects.

Question 130

At fictional Lakeshore Finance, a network engineer supporting transaction systems is reviewing route-policy and traffic-control behavior during a lab-to-production acceptance (HCIP-H12-821-POLICY-033). The observed network issue is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. Which ongoing preventive or detective control would best reduce recurrence?

  1. Validate policer and shaper action selection against traffic SLAs.
  2. Compare advertised communities and final export decisions after policy updates.
  3. Check trust boundary and classification counters before measuring QoS outcome.
  4. Build source-destination acceptance matrices for policy-based routing.

Explanation

Correct Answer

D:

The preventive or detective safeguard is: Build source-destination acceptance matrices for policy-based routing. This directly addresses the recurring fault: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. The corrective action would be: Generate probes from each intended source address or VLAN and observe policy match statistics. Success is demonstrated when: Every planned source group uses its assigned path with no unintended routing side effects.

Incorrect Answers

A:

“Validate policer and shaper action selection against traffic SLAs” addresses recurrence of another problem: A Huawei MQC behavior applies policing at an uplink but the operator expects it to buffer all excess traffic. That problem depends on: The preventive or detective safeguard is: Validate policer and shaper action selection against traffic SLAs. The recurring risk here is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. The more targeted safeguard is “Build source-destination acceptance matrices for policy-based routing” because the preventive or detective safeguard is: Build source-destination acceptance matrices for policy-based routing.

B:

“Compare advertised communities and final export decisions after policy updates” addresses recurrence of another problem: An engineer sets a BGP route community but forgets the matching export policy and upstream advertisements are unchanged. That problem depends on: The preventive or detective safeguard is: Compare advertised communities and final export decisions after policy updates. The recurring risk here is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. The more targeted safeguard is “Build source-destination acceptance matrices for policy-based routing” because the preventive or detective safeguard is: Build source-destination acceptance matrices for policy-based routing.

C:

“Check trust boundary and classification counters before measuring QoS outcome” addresses recurrence of another problem: A classifier matches the wrong VLAN priority bits and high-priority voice is treated as bulk data. That problem depends on: The preventive or detective safeguard is: Check trust boundary and classification counters before measuring QoS outcome. The recurring risk here is: A traffic-engineering plan changes route selection but the test validates only traceroute from the wrong source network. The more targeted safeguard is “Build source-destination acceptance matrices for policy-based routing” because the preventive or detective safeguard is: Build source-destination acceptance matrices for policy-based routing.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests