McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 52

Question 510

At fictional Oakridge Energy, a network engineer supporting field substations is reviewing IGMP and PIM multicast distribution during a baseline compliance test (HCIP-H12-821-MULTICAST-128). The observed network issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. Which next engineering action best addresses the reported problem?

  1. Correct unicast route reachability or multicast RPF path so the incoming interface is valid.
  2. Align IGMP version support and receiver source-filtering expectations.
  3. Enable and validate PIM on all required routed multicast hops in the distribution tree.
  4. Configure supported IGMP snooping and confirm correct listener port learning.

Explanation

Correct Answer

D:

The directly responsive action is: Configure supported IGMP snooping and confirm correct listener port learning. The specific reported fault is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. Confirmation should show: Stream traffic is limited to known interested ports and any required router-facing links. The supporting technical principle is: IGMP snooping constrains layer-2 multicast replication by observing group membership.

Incorrect Answers

A:

“Correct unicast route reachability or multicast RPF path so the incoming interface is valid” responds to another technical or business failure: A multicast forwarding entry receives traffic from a source on the wrong interface and drops it. That source case depends on: Multicast routing uses reverse-path-forwarding checks to prevent loops. The present issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more direct action is “Configure supported IGMP snooping and confirm correct listener port learning” because IGMP snooping constrains layer-2 multicast replication by observing group membership.

B:

“Align IGMP version support and receiver source-filtering expectations” responds to another technical or business failure: A network expects IGMPv3 source-specific filtering but uses routers configured only for IGMPv2. That source case depends on: IGMPv3 adds source filtering required for source-specific multicast operation. The present issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more direct action is “Configure supported IGMP snooping and confirm correct listener port learning” because IGMP snooping constrains layer-2 multicast replication by observing group membership.

C:

“Enable and validate PIM on all required routed multicast hops in the distribution tree” responds to another technical or business failure: A multicast receiver has IGMP state locally but the PIM upstream interface is disabled. That source case depends on: Local IGMP membership alone does not carry multicast across routed PIM boundaries. The present issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more direct action is “Configure supported IGMP snooping and confirm correct listener port learning” because IGMP snooping constrains layer-2 multicast replication by observing group membership.

Question 511

At fictional Oakridge Energy, a network engineer supporting field substations is reviewing IGMP and PIM multicast distribution during a baseline compliance test (HCIP-H12-821-MULTICAST-128). The observed network issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. Which ongoing preventive or detective control would best reduce recurrence?

  1. Validate snooping memberships after each VLAN access change.
  2. Maintain a group-address registry for application onboarding.
  3. Record IGMP version compatibility for source-filtered applications.
  4. Check the querier role and aging timers during multicast incidents.

Explanation

Correct Answer

A:

The preventive or detective safeguard is: Validate snooping memberships after each VLAN access change. This directly addresses the recurring fault: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The corrective action would be: Configure supported IGMP snooping and confirm correct listener port learning. Success is demonstrated when: Stream traffic is limited to known interested ports and any required router-facing links.

Incorrect Answers

B:

“Maintain a group-address registry for application onboarding” addresses recurrence of another problem: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. That problem depends on: The preventive or detective safeguard is: Maintain a group-address registry for application onboarding. The recurring risk here is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more targeted safeguard is “Validate snooping memberships after each VLAN access change” because the preventive or detective safeguard is: Validate snooping memberships after each VLAN access change.

C:

“Record IGMP version compatibility for source-filtered applications” addresses recurrence of another problem: A network expects IGMPv3 source-specific filtering but uses routers configured only for IGMPv2. That problem depends on: The preventive or detective safeguard is: Record IGMP version compatibility for source-filtered applications. The recurring risk here is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more targeted safeguard is “Validate snooping memberships after each VLAN access change” because the preventive or detective safeguard is: Validate snooping memberships after each VLAN access change.

D:

“Check the querier role and aging timers during multicast incidents” addresses recurrence of another problem: A multicast router sees no group receivers because IGMP query messages are absent from a VLAN. That problem depends on: The preventive or detective safeguard is: Check the querier role and aging timers during multicast incidents. The recurring risk here is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more targeted safeguard is “Validate snooping memberships after each VLAN access change” because the preventive or detective safeguard is: Validate snooping memberships after each VLAN access change.

Question 512

At fictional Oakridge Energy, a network engineer supporting field substations is reviewing IGMP and PIM multicast distribution during a baseline compliance test (HCIP-H12-821-MULTICAST-128). The observed network issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. Which observation most directly verifies that the corrective change succeeded?

  1. Stream traffic is limited to known interested ports and any required router-facing links.
  2. PIM neighbor and forwarding states are present along the route to the source or RP.
  3. Only intended receivers for each service group see the correct media flow.
  4. Client memberships are refreshed and multicast packets reach subscribed hosts.

Explanation

Correct Answer

A:

The best verification observation is: Stream traffic is limited to known interested ports and any required router-facing links. It demonstrates the corrective action: Configure supported IGMP snooping and confirm correct listener port learning. This fits the principle: IGMP snooping constrains layer-2 multicast replication by observing group membership. Verify on the actual Huawei platform and network release.

Incorrect Answers

B:

“PIM neighbor and forwarding states are present along the route to the source or RP” responds to another technical or business failure: A multicast receiver has IGMP state locally but the PIM upstream interface is disabled. That source case depends on: The best verification observation is: PIM neighbor and forwarding states are present along the route to the source or RP. The present issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more direct action is “Stream traffic is limited to known interested ports and any required router-facing links” because the best verification observation is: Stream traffic is limited to known interested ports and any required router-facing links.

C:

“Only intended receivers for each service group see the correct media flow” responds to another technical or business failure: Multicast packets arrive at the wrong group because the sender application uses a group address overlapping another service. That source case depends on: The best verification observation is: Only intended receivers for each service group see the correct media flow. The present issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more direct action is “Stream traffic is limited to known interested ports and any required router-facing links” because the best verification observation is: Stream traffic is limited to known interested ports and any required router-facing links.

D:

“Client memberships are refreshed and multicast packets reach subscribed hosts” responds to another technical or business failure: A multicast router sees no group receivers because IGMP query messages are absent from a VLAN. That source case depends on: The best verification observation is: Client memberships are refreshed and multicast packets reach subscribed hosts. The present issue is: A receiver sends IGMP membership reports but the local VLAN switch floods the multicast group to every port. The more direct action is “Stream traffic is limited to known interested ports and any required router-facing links” because the best verification observation is: Stream traffic is limited to known interested ports and any required router-facing links.

Question 513

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing BGP routing, path attributes and EVPN exchange during a production cutover (HCIP-H12-821-BGP-129). The observed network issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. Which observation most directly verifies that the corrective change succeeded?

  1. Correct tenant MAC routes appear only in the intended bridge domain.
  2. Type 5 IP routes and Type 2 MAC reachability are present where each service requires them.
  3. The aggregate is advertised with working forwarding paths to all intended destinations.
  4. Distinct VPN routes remain distinguishable and only intended tenants import advertisements.

Explanation

Correct Answer

B:

The best verification observation is: Type 5 IP routes and Type 2 MAC reachability are present where each service requires them. It demonstrates the corrective action: Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability. This fits the principle: EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“Correct tenant MAC routes appear only in the intended bridge domain” responds to another technical or business failure: A fabric advertises a host MAC under the wrong VNI and an engineer changes the global underlay OSPF cost to compensate. That source case depends on: The best verification observation is: Correct tenant MAC routes appear only in the intended bridge domain. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “Type 5 IP routes and Type 2 MAC reachability are present where each service requires them” because the best verification observation is: Type 5 IP routes and Type 2 MAC reachability are present where each service requires them.

C:

“The aggregate is advertised with working forwarding paths to all intended destinations” responds to another technical or business failure: An operator creates a BGP aggregate but traffic is black-holed because no specific reachable next hop supports it. That source case depends on: The best verification observation is: The aggregate is advertised with working forwarding paths to all intended destinations. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “Type 5 IP routes and Type 2 MAC reachability are present where each service requires them” because the best verification observation is: Type 5 IP routes and Type 2 MAC reachability are present where each service requires them.

D:

“Distinct VPN routes remain distinguishable and only intended tenants import advertisements” responds to another technical or business failure: A network architect uses an EVPN route distinguisher expecting it to automatically control which VPNs import the route. That source case depends on: The best verification observation is: Distinct VPN routes remain distinguishable and only intended tenants import advertisements. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “Type 5 IP routes and Type 2 MAC reachability are present where each service requires them” because the best verification observation is: Type 5 IP routes and Type 2 MAC reachability are present where each service requires them.

Question 514

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing BGP routing, path attributes and EVPN exchange during a production cutover (HCIP-H12-821-BGP-129). The observed network issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. Which ongoing preventive or detective control would best reduce recurrence?

  1. Validate both reflected path visibility and next-hop recursion on clients.
  2. Review imported local preference on all border routers after ISP changes.
  3. Map service intent to EVPN route type during VXLAN design.
  4. Review RR client status and prefix visibility after each router addition.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Map service intent to EVPN route type during VXLAN design. This directly addresses the recurring fault: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The corrective action would be: Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability. Success is demonstrated when: Type 5 IP routes and Type 2 MAC reachability are present where each service requires them.

Incorrect Answers

A:

“Validate both reflected path visibility and next-hop recursion on clients” addresses recurrence of another problem: A route reflector receives a new external prefix but its clients cannot use the route because the advertised next hop is unreachable. That problem depends on: The preventive or detective safeguard is: Validate both reflected path visibility and next-hop recursion on clients. The recurring risk here is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more targeted safeguard is “Map service intent to EVPN route type during VXLAN design” because the preventive or detective safeguard is: Map service intent to EVPN route type during VXLAN design.

B:

“Review imported local preference on all border routers after ISP changes” addresses recurrence of another problem: Two external BGP exits learn the same remote prefix and a company needs consistent outbound preference inside the AS. That problem depends on: The preventive or detective safeguard is: Review imported local preference on all border routers after ISP changes. The recurring risk here is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more targeted safeguard is “Map service intent to EVPN route type during VXLAN design” because the preventive or detective safeguard is: Map service intent to EVPN route type during VXLAN design.

D:

“Review RR client status and prefix visibility after each router addition” addresses recurrence of another problem: An enterprise has too many iBGP sessions and introduces a route reflector without identifying its client peers. That problem depends on: The preventive or detective safeguard is: Review RR client status and prefix visibility after each router addition. The recurring risk here is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more targeted safeguard is “Map service intent to EVPN route type during VXLAN design” because the preventive or detective safeguard is: Map service intent to EVPN route type during VXLAN design.

Question 515

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing BGP routing, path attributes and EVPN exchange during a production cutover (HCIP-H12-821-BGP-129). The observed network issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. Which next engineering action best addresses the reported problem?

  1. Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability.
  2. Review MED comparison scope and any explicit policy for peers from different autonomous systems.
  3. Validate supporting component routes and safe aggregate generation or discard behavior.
  4. Differentiate retained alternatives, chosen best path and supported multipath forwarding configuration.

Explanation

Correct Answer

A:

The directly responsive action is: Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability. The specific reported fault is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. Confirmation should show: Type 5 IP routes and Type 2 MAC reachability are present where each service requires them. The supporting technical principle is: EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.

Incorrect Answers

B:

“Review MED comparison scope and any explicit policy for peers from different autonomous systems” responds to another technical or business failure: A multi-exit BGP neighbor advertises a preferred MED but the local router compares routes from unrelated upstream ASes incorrectly. That source case depends on: MED can influence entry choice but default comparisons and import policy constrain its use. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability” because EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.

C:

“Validate supporting component routes and safe aggregate generation or discard behavior” responds to another technical or business failure: An operator creates a BGP aggregate but traffic is black-holed because no specific reachable next hop supports it. That source case depends on: BGP aggregation must be consistent with actual routed component reachability. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability” because EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.

D:

“Differentiate retained alternatives, chosen best path and supported multipath forwarding configuration” responds to another technical or business failure: A BGP router receives multiple paths and engineering assumes all alternate paths must be installed for forwarding regardless of BGP capability. That source case depends on: BGP can retain multiple paths while installing selected forwarding entries under platform rules. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability” because EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.

Question 516

At fictional Granite Logistics, a network engineer supporting warehouse distribution is reviewing BGP routing, path attributes and EVPN exchange during a production cutover (HCIP-H12-821-BGP-129). The observed network issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. Which routing, switching, or network principle best explains the appropriate solution?

  1. Overlay service identifiers control tenant membership independently of underlay reachability.
  2. BGP path attributes are compared in an ordered selection process, not by AS_PATH alone.
  3. EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.
  4. BGP TCP endpoints must match peer configuration and be routable in both directions.

Explanation

Correct Answer

C:

The governing principle is: EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement. In this scenario, the appropriate action is: Choose the correct EVPN route type for IP prefix routing versus bridged endpoint MAC reachability. Valid evidence would show: Type 5 IP routes and Type 2 MAC reachability are present where each service requires them.

Incorrect Answers

A:

“Overlay service identifiers control tenant membership independently of underlay reachability” responds to another technical or business failure: A fabric advertises a host MAC under the wrong VNI and an engineer changes the global underlay OSPF cost to compensate. That source case depends on: Overlay service identifiers control tenant membership independently of underlay reachability. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement” because EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.

B:

“BGP path attributes are compared in an ordered selection process, not by AS_PATH alone” responds to another technical or business failure: Two customer-facing links show unequal AS_PATH lengths and operators insist the longer path is always preferred regardless of policy. That source case depends on: BGP path attributes are compared in an ordered selection process, not by AS_PATH alone. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement” because EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.

D:

“BGP TCP endpoints must match peer configuration and be routable in both directions” responds to another technical or business failure: An iBGP adjacency to peer loopbacks fails because one side sends TCP from the physical interface address. That source case depends on: BGP TCP endpoints must match peer configuration and be routable in both directions. The present issue is: An engineer expects BGP EVPN Type 5 IP prefixes to replace all MAC learning requirements for a layer-2 stretch. The more direct action is “EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement” because EVPN route types distinguish IP-prefix advertisement from MAC/IP advertisement.

Question 517

At fictional Dovetail University, a network engineer supporting campus routing is reviewing OSPF area design and link-state convergence during a customer network audit (HCIP-H12-821-OSPF-130). The observed network issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. Which next engineering action best addresses the reported problem?

  1. Compare E1 versus E2 metric handling and evaluate route selection under competing exits.
  2. Investigate bidirectional Hello reception and permitted multicast or interface filtering on the segment.
  3. Locate the unstable interface and review SPF scheduling while repairing the physical source of churn.
  4. Apply compatible authentication settings and keys on both interfaces under controlled change.

Explanation

Correct Answer

A:

The directly responsive action is: Compare E1 versus E2 metric handling and evaluate route selection under competing exits. The specific reported fault is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. Confirmation should show: Competing ASBR paths select according to the defined external metric type and tie-breaking cost. The supporting technical principle is: OSPF E1 and E2 external cost calculations treat internal path costs differently.

Incorrect Answers

B:

“Investigate bidirectional Hello reception and permitted multicast or interface filtering on the segment” responds to another technical or business failure: A transit OSPF link remains in Init because one router never sees its own router ID listed in neighbor Hellos. That source case depends on: OSPF two-way communication is established only after reciprocal Hello discovery. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “Compare E1 versus E2 metric handling and evaluate route selection under competing exits” because OSPF E1 and E2 external cost calculations treat internal path costs differently.

C:

“Locate the unstable interface and review SPF scheduling while repairing the physical source of churn” responds to another technical or business failure: A router repeatedly runs SPF after frequent interface state changes and application latency rises. That source case depends on: Repeated link-state topology changes cause repeated shortest-path recomputation. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “Compare E1 versus E2 metric handling and evaluate route selection under competing exits” because OSPF E1 and E2 external cost calculations treat internal path costs differently.

D:

“Apply compatible authentication settings and keys on both interfaces under controlled change” responds to another technical or business failure: An OSPF adjacency repeatedly fails due to mismatched authentication algorithms after a maintenance window. That source case depends on: OSPF routing exchanges depend on matched authentication parameters when authentication is enabled. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “Compare E1 versus E2 metric handling and evaluate route selection under competing exits” because OSPF E1 and E2 external cost calculations treat internal path costs differently.

Question 518

At fictional Dovetail University, a network engineer supporting campus routing is reviewing OSPF area design and link-state convergence during a customer network audit (HCIP-H12-821-OSPF-130). The observed network issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. Which routing, switching, or network principle best explains the appropriate solution?

  1. Broadcast OSPF does not require every pair of DROthers to form a full adjacency.
  2. OSPF detects neighbor failure using liveness Hellos that can be impacted by packet loss.
  3. OSPF E1 and E2 external cost calculations treat internal path costs differently.
  4. OSPF process activation on interfaces depends on matching enabled prefixes and area configuration.

Explanation

Correct Answer

C:

The governing principle is: OSPF E1 and E2 external cost calculations treat internal path costs differently. In this scenario, the appropriate action is: Compare E1 versus E2 metric handling and evaluate route selection under competing exits. Valid evidence would show: Competing ASBR paths select according to the defined external metric type and tie-breaking cost.

Incorrect Answers

A:

“Broadcast OSPF does not require every pair of DROthers to form a full adjacency” responds to another technical or business failure: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. That source case depends on: Broadcast OSPF does not require every pair of DROthers to form a full adjacency. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “OSPF E1 and E2 external cost calculations treat internal path costs differently” because OSPF E1 and E2 external cost calculations treat internal path costs differently.

B:

“OSPF detects neighbor failure using liveness Hellos that can be impacted by packet loss” responds to another technical or business failure: An OSPF neighbor oscillates between Full and Down on a congested shared segment despite correct area IDs. That source case depends on: OSPF detects neighbor failure using liveness Hellos that can be impacted by packet loss. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “OSPF E1 and E2 external cost calculations treat internal path costs differently” because OSPF E1 and E2 external cost calculations treat internal path costs differently.

D:

“OSPF process activation on interfaces depends on matching enabled prefixes and area configuration” responds to another technical or business failure: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. That source case depends on: OSPF process activation on interfaces depends on matching enabled prefixes and area configuration. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “OSPF E1 and E2 external cost calculations treat internal path costs differently” because OSPF E1 and E2 external cost calculations treat internal path costs differently.

Question 519

At fictional Dovetail University, a network engineer supporting campus routing is reviewing OSPF area design and link-state convergence during a customer network audit (HCIP-H12-821-OSPF-130). The observed network issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. Which observation most directly verifies that the corrective change succeeded?

  1. Competing ASBR paths select according to the defined external metric type and tie-breaking cost.
  2. The preferred and backup paths match the documented effective costs.
  3. The area border router maintains backbone reachability and remote area routes appear.
  4. The backbone receives the intended external aggregate and required exceptions.

Explanation

Correct Answer

A:

The best verification observation is: Competing ASBR paths select according to the defined external metric type and tie-breaking cost. It demonstrates the corrective action: Compare E1 versus E2 metric handling and evaluate route selection under competing exits. This fits the principle: OSPF E1 and E2 external cost calculations treat internal path costs differently. Verify on the actual Huawei platform and network release.

Incorrect Answers

B:

“The preferred and backup paths match the documented effective costs” responds to another technical or business failure: A failover design sets interface bandwidth but ignores manually configured OSPF costs that override the intended metric. That source case depends on: The best verification observation is: The preferred and backup paths match the documented effective costs. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “Competing ASBR paths select according to the defined external metric type and tie-breaking cost” because the best verification observation is: Competing ASBR paths select according to the defined external metric type and tie-breaking cost.

C:

“The area border router maintains backbone reachability and remote area routes appear” responds to another technical or business failure: A branch area has no direct backbone connectivity and operators try to exchange routes between nonbackbone areas directly. That source case depends on: The best verification observation is: The area border router maintains backbone reachability and remote area routes appear. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “Competing ASBR paths select according to the defined external metric type and tie-breaking cost” because the best verification observation is: Competing ASBR paths select according to the defined external metric type and tie-breaking cost.

D:

“The backbone receives the intended external aggregate and required exceptions” responds to another technical or business failure: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. That source case depends on: The best verification observation is: The backbone receives the intended external aggregate and required exceptions. The present issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more direct action is “Competing ASBR paths select according to the defined external metric type and tie-breaking cost” because the best verification observation is: Competing ASBR paths select according to the defined external metric type and tie-breaking cost.

Question 520

At fictional Dovetail University, a network engineer supporting campus routing is reviewing OSPF area design and link-state convergence during a customer network audit (HCIP-H12-821-OSPF-130). The observed network issue is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. Which ongoing preventive or detective control would best reduce recurrence?

  1. Record configured effective costs during WAN circuit upgrades.
  2. Validate each constituent prefix and failover behavior under a planned aggregate.
  3. Compare redistributed prefix lists and Type 5 presence in each permitted area.
  4. State E1 or E2 design intent in redistribution policies and validate dual exits.

Explanation

Correct Answer

D:

The preventive or detective safeguard is: State E1 or E2 design intent in redistribution policies and validate dual exits. This directly addresses the recurring fault: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The corrective action would be: Compare E1 versus E2 metric handling and evaluate route selection under competing exits. Success is demonstrated when: Competing ASBR paths select according to the defined external metric type and tie-breaking cost.

Incorrect Answers

A:

“Record configured effective costs during WAN circuit upgrades” addresses recurrence of another problem: A failover design sets interface bandwidth but ignores manually configured OSPF costs that override the intended metric. That problem depends on: The preventive or detective safeguard is: Record configured effective costs during WAN circuit upgrades. The recurring risk here is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more targeted safeguard is “State E1 or E2 design intent in redistribution policies and validate dual exits” because the preventive or detective safeguard is: State E1 or E2 design intent in redistribution policies and validate dual exits.

B:

“Validate each constituent prefix and failover behavior under a planned aggregate” addresses recurrence of another problem: An OSPF summary aggregate covers a disconnected subnet and an engineer assumes all summarized addresses have valid next hops. That problem depends on: The preventive or detective safeguard is: Validate each constituent prefix and failover behavior under a planned aggregate. The recurring risk here is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more targeted safeguard is “State E1 or E2 design intent in redistribution policies and validate dual exits” because the preventive or detective safeguard is: State E1 or E2 design intent in redistribution policies and validate dual exits.

C:

“Compare redistributed prefix lists and Type 5 presence in each permitted area” addresses recurrence of another problem: An ASBR redistributes a static service subnet but other areas never see its external OSPF destination. That problem depends on: The preventive or detective safeguard is: Compare redistributed prefix lists and Type 5 presence in each permitted area. The recurring risk here is: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. The more targeted safeguard is “State E1 or E2 design intent in redistribution policies and validate dual exits” because the preventive or detective safeguard is: State E1 or E2 design intent in redistribution policies and validate dual exits.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests