McAfee Secure

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

Huawei H12-821 Questions & Answers

Study with Up-To-Date REAL Exam Questions and Answers from the ACTUAL Test

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 21

Question 200

At fictional Beacon Healthcare, a network engineer supporting hospital network services is reviewing IPv6 addressing and neighbor discovery during a network troubleshooting drill (HCIP-H12-821-IPV6-050). The observed network issue is: An IPv6 access host uses an incorrect address despite receiving a valid network prefix because the advertised M and O flags are misunderstood. Which routing, switching, or network principle best explains the appropriate solution?

  1. Equal-cost shortest paths must also be installed under platform ECMP constraints.
  2. BGP FSM states distinguish session formation failures from routing-update processing.
  3. IPv6 addressing, NDP and route selection are separate prerequisites for forwarding.
  4. IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior.

Explanation

Correct Answer

D:

The governing principle is: IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior. In this scenario, the appropriate action is: Check RA autonomous prefix flags and DHCPv6 managed or other-configuration signaling. Valid evidence would show: Hosts obtain the intended SLAAC or DHCPv6 address and ancillary configuration.

Incorrect Answers

A:

“Equal-cost shortest paths must also be installed under platform ECMP constraints” responds to another technical or business failure: Two equal-cost OSPF paths exist but traffic uses only one because the forwarding configuration limits ECMP. That source case depends on: Equal-cost shortest paths must also be installed under platform ECMP constraints. The present issue is: An IPv6 access host uses an incorrect address despite receiving a valid network prefix because the advertised M and O flags are misunderstood. The more direct action is “IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior” because IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior.

B:

“BGP FSM states distinguish session formation failures from routing-update processing” responds to another technical or business failure: BGP stays in Idle after a new neighbor is configured and operators troubleshoot route policies instead of local interface reachability. That source case depends on: BGP FSM states distinguish session formation failures from routing-update processing. The present issue is: An IPv6 access host uses an incorrect address despite receiving a valid network prefix because the advertised M and O flags are misunderstood. The more direct action is “IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior” because IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior.

C:

“IPv6 addressing, NDP and route selection are separate prerequisites for forwarding” responds to another technical or business failure: An engineer configures an IPv6 global unicast address but assumes this automatically establishes external default routing. That source case depends on: IPv6 addressing, NDP and route selection are separate prerequisites for forwarding. The present issue is: An IPv6 access host uses an incorrect address despite receiving a valid network prefix because the advertised M and O flags are misunderstood. The more direct action is “IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior” because IPv6 RA flags and prefix options influence autonomous and stateful configuration behavior.

Question 201

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing OSPF area design and link-state convergence during a production cutover (HCIP-H12-821-OSPF-051). The observed network issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. Which ongoing preventive or detective control would best reduce recurrence?

  1. Compare area IDs in both directions during OSPF adjacency acceptance.
  2. Include interface participation checks in subnet migration procedures.
  3. Record each special-area role and inspect LSA types after ABR changes.
  4. Trend OSPF adjacency and SPF event rates alongside interface health.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Record each special-area role and inspect LSA types after ABR changes. This directly addresses the recurring fault: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The corrective action would be: Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements. Success is demonstrated when: The intended default route is available and detailed inter-area summaries are suppressed as designed.

Incorrect Answers

A:

“Compare area IDs in both directions during OSPF adjacency acceptance” addresses recurrence of another problem: Two neighboring Huawei routers exchange Hello packets but never become OSPF neighbors because their area identifiers differ. That problem depends on: The preventive or detective safeguard is: Compare area IDs in both directions during OSPF adjacency acceptance. The recurring risk here is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more targeted safeguard is “Record each special-area role and inspect LSA types after ABR changes” because the preventive or detective safeguard is: Record each special-area role and inspect LSA types after ABR changes.

B:

“Include interface participation checks in subnet migration procedures” addresses recurrence of another problem: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. That problem depends on: The preventive or detective safeguard is: Include interface participation checks in subnet migration procedures. The recurring risk here is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more targeted safeguard is “Record each special-area role and inspect LSA types after ABR changes” because the preventive or detective safeguard is: Record each special-area role and inspect LSA types after ABR changes.

D:

“Trend OSPF adjacency and SPF event rates alongside interface health” addresses recurrence of another problem: A router repeatedly runs SPF after frequent interface state changes and application latency rises. That problem depends on: The preventive or detective safeguard is: Trend OSPF adjacency and SPF event rates alongside interface health. The recurring risk here is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more targeted safeguard is “Record each special-area role and inspect LSA types after ABR changes” because the preventive or detective safeguard is: Record each special-area role and inspect LSA types after ABR changes.

Question 202

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing OSPF area design and link-state convergence during a production cutover (HCIP-H12-821-OSPF-051). The observed network issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. Which observation most directly verifies that the corrective change succeeded?

  1. The interfaces agree on area ID and reach the expected OSPF neighbor state.
  2. The intended default route is available and detailed inter-area summaries are suppressed as designed.
  3. The device stays ineligible for DR election while eligible peers hold the role.
  4. The area border router maintains backbone reachability and remote area routes appear.

Explanation

Correct Answer

B:

The best verification observation is: The intended default route is available and detailed inter-area summaries are suppressed as designed. It demonstrates the corrective action: Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements. This fits the principle: Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“The interfaces agree on area ID and reach the expected OSPF neighbor state” responds to another technical or business failure: Two neighboring Huawei routers exchange Hello packets but never become OSPF neighbors because their area identifiers differ. That source case depends on: The best verification observation is: The interfaces agree on area ID and reach the expected OSPF neighbor state. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “The intended default route is available and detailed inter-area summaries are suppressed as designed” because the best verification observation is: The intended default route is available and detailed inter-area summaries are suppressed as designed.

C:

“The device stays ineligible for DR election while eligible peers hold the role” responds to another technical or business failure: A new router with OSPF priority zero fails to become the designated router even after repeated interface bounces. That source case depends on: The best verification observation is: The device stays ineligible for DR election while eligible peers hold the role. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “The intended default route is available and detailed inter-area summaries are suppressed as designed” because the best verification observation is: The intended default route is available and detailed inter-area summaries are suppressed as designed.

D:

“The area border router maintains backbone reachability and remote area routes appear” responds to another technical or business failure: A branch area has no direct backbone connectivity and operators try to exchange routes between nonbackbone areas directly. That source case depends on: The best verification observation is: The area border router maintains backbone reachability and remote area routes appear. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “The intended default route is available and detailed inter-area summaries are suppressed as designed” because the best verification observation is: The intended default route is available and detailed inter-area summaries are suppressed as designed.

Question 203

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing OSPF area design and link-state convergence during a production cutover (HCIP-H12-821-OSPF-051). The observed network issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. Which routing, switching, or network principle best explains the appropriate solution?

  1. OSPF route installation filtering is not necessarily equivalent to suppressing flooded LSAs.
  2. Repeated link-state topology changes cause repeated shortest-path recomputation.
  3. Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.
  4. Stub OSPF areas suppress ordinary external LSAs and rely on area-appropriate reachability.

Explanation

Correct Answer

C:

The governing principle is: Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions. In this scenario, the appropriate action is: Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements. Valid evidence would show: The intended default route is available and detailed inter-area summaries are suppressed as designed.

Incorrect Answers

A:

“OSPF route installation filtering is not necessarily equivalent to suppressing flooded LSAs” responds to another technical or business failure: An engineer uses a prefix-filter on one OSPF router expecting to prevent every other router from receiving the LSA. That source case depends on: OSPF route installation filtering is not necessarily equivalent to suppressing flooded LSAs. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions” because Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.

B:

“Repeated link-state topology changes cause repeated shortest-path recomputation” responds to another technical or business failure: A router repeatedly runs SPF after frequent interface state changes and application latency rises. That source case depends on: Repeated link-state topology changes cause repeated shortest-path recomputation. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions” because Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.

D:

“Stub OSPF areas suppress ordinary external LSAs and rely on area-appropriate reachability” responds to another technical or business failure: A default route disappears inside an OSPF stub area because engineers expect external Type 5 LSAs to flood normally. That source case depends on: Stub OSPF areas suppress ordinary external LSAs and rely on area-appropriate reachability. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions” because Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.

Question 204

At fictional Cedar Retail, a network engineer supporting store connectivity is reviewing OSPF area design and link-state convergence during a production cutover (HCIP-H12-821-OSPF-051). The observed network issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. Which next engineering action best addresses the reported problem?

  1. Align compatible OSPF network types and validate hello and DR behavior for the actual media.
  2. Align interface OSPF area assignment on both ends without changing unrelated adjacencies.
  3. Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements.
  4. Inspect external redistribution configuration, LSA Type 5 generation and area restrictions.

Explanation

Correct Answer

C:

The directly responsive action is: Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements. The specific reported fault is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. Confirmation should show: The intended default route is available and detailed inter-area summaries are suppressed as designed. The supporting technical principle is: Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.

Incorrect Answers

A:

“Align compatible OSPF network types and validate hello and DR behavior for the actual media” responds to another technical or business failure: Two OSPF devices on a point-to-point fiber cannot build an adjacency because their interface network types differ. That source case depends on: OSPF interface network type affects neighbor handling and designated router behavior. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements” because Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.

B:

“Align interface OSPF area assignment on both ends without changing unrelated adjacencies” responds to another technical or business failure: Two neighboring Huawei routers exchange Hello packets but never become OSPF neighbors because their area identifiers differ. That source case depends on: OSPF neighbor formation requires matching area configuration on shared links. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements” because Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.

D:

“Inspect external redistribution configuration, LSA Type 5 generation and area restrictions” responds to another technical or business failure: An ASBR redistributes a static service subnet but other areas never see its external OSPF destination. That source case depends on: OSPF external routing requires correctly originated and flooded AS-external LSAs. The present issue is: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. The more direct action is “Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements” because Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions.

Question 205

At fictional Juniper Publishing, a network engineer supporting hybrid offices is reviewing OSPF area design and link-state convergence during a new network integration (HCIP-H12-821-OSPF-052). The observed network issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. Which observation most directly verifies that the corrective change succeeded?

  1. The intended interface participates in OSPF and its prefix is announced appropriately.
  2. The receiving area learns approved inter-area prefixes through expected summary LSAs.
  3. The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR.
  4. The interfaces agree on area ID and reach the expected OSPF neighbor state.

Explanation

Correct Answer

C:

The best verification observation is: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR. It demonstrates the corrective action: Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR. This fits the principle: Broadcast OSPF does not require every pair of DROthers to form a full adjacency. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“The intended interface participates in OSPF and its prefix is announced appropriately” responds to another technical or business failure: OSPF adjacency is stable but a route to a target subnet is absent due to network-statement matching mistakes. That source case depends on: The best verification observation is: The intended interface participates in OSPF and its prefix is announced appropriately. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR” because the best verification observation is: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR.

B:

“The receiving area learns approved inter-area prefixes through expected summary LSAs” responds to another technical or business failure: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. That source case depends on: The best verification observation is: The receiving area learns approved inter-area prefixes through expected summary LSAs. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR” because the best verification observation is: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR.

D:

“The interfaces agree on area ID and reach the expected OSPF neighbor state” responds to another technical or business failure: Two neighboring Huawei routers exchange Hello packets but never become OSPF neighbors because their area identifiers differ. That source case depends on: The best verification observation is: The interfaces agree on area ID and reach the expected OSPF neighbor state. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR” because the best verification observation is: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR.

Question 206

At fictional Juniper Publishing, a network engineer supporting hybrid offices is reviewing OSPF area design and link-state convergence during a new network integration (HCIP-H12-821-OSPF-052). The observed network issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. Which ongoing preventive or detective control would best reduce recurrence?

  1. Compare redistributed prefix lists and Type 5 presence in each permitted area.
  2. Monitor neighbor resets and interface congestion together during incident triage.
  3. Verify neighbor roles before escalating stable 2-Way observations.
  4. Review ASBR summarized route contents before production advertisement.

Explanation

Correct Answer

C:

The preventive or detective safeguard is: Verify neighbor roles before escalating stable 2-Way observations. This directly addresses the recurring fault: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The corrective action would be: Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR. Success is demonstrated when: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR.

Incorrect Answers

A:

“Compare redistributed prefix lists and Type 5 presence in each permitted area” addresses recurrence of another problem: An ASBR redistributes a static service subnet but other areas never see its external OSPF destination. That problem depends on: The preventive or detective safeguard is: Compare redistributed prefix lists and Type 5 presence in each permitted area. The recurring risk here is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more targeted safeguard is “Verify neighbor roles before escalating stable 2-Way observations” because the preventive or detective safeguard is: Verify neighbor roles before escalating stable 2-Way observations.

B:

“Monitor neighbor resets and interface congestion together during incident triage” addresses recurrence of another problem: An OSPF neighbor oscillates between Full and Down on a congested shared segment despite correct area IDs. That problem depends on: The preventive or detective safeguard is: Monitor neighbor resets and interface congestion together during incident triage. The recurring risk here is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more targeted safeguard is “Verify neighbor roles before escalating stable 2-Way observations” because the preventive or detective safeguard is: Verify neighbor roles before escalating stable 2-Way observations.

D:

“Review ASBR summarized route contents before production advertisement” addresses recurrence of another problem: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. That problem depends on: The preventive or detective safeguard is: Review ASBR summarized route contents before production advertisement. The recurring risk here is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more targeted safeguard is “Verify neighbor roles before escalating stable 2-Way observations” because the preventive or detective safeguard is: Verify neighbor roles before escalating stable 2-Way observations.

Question 207

At fictional Juniper Publishing, a network engineer supporting hybrid offices is reviewing OSPF area design and link-state convergence during a new network integration (HCIP-H12-821-OSPF-052). The observed network issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. Which routing, switching, or network principle best explains the appropriate solution?

  1. OSPF interface network type affects neighbor handling and designated router behavior.
  2. Broadcast OSPF does not require every pair of DROthers to form a full adjacency.
  3. Incompatible interface MTU can interrupt OSPF database synchronization.
  4. OSPF area border routers convey inter-area network reachability using summary information.

Explanation

Correct Answer

B:

The governing principle is: Broadcast OSPF does not require every pair of DROthers to form a full adjacency. In this scenario, the appropriate action is: Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR. Valid evidence would show: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR.

Incorrect Answers

A:

“OSPF interface network type affects neighbor handling and designated router behavior” responds to another technical or business failure: Two OSPF devices on a point-to-point fiber cannot build an adjacency because their interface network types differ. That source case depends on: OSPF interface network type affects neighbor handling and designated router behavior. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “Broadcast OSPF does not require every pair of DROthers to form a full adjacency” because Broadcast OSPF does not require every pair of DROthers to form a full adjacency.

C:

“Incompatible interface MTU can interrupt OSPF database synchronization” responds to another technical or business failure: An OSPF neighbor stays in Exchange and large database description packets fail over a reduced-MTU tunnel. That source case depends on: Incompatible interface MTU can interrupt OSPF database synchronization. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “Broadcast OSPF does not require every pair of DROthers to form a full adjacency” because Broadcast OSPF does not require every pair of DROthers to form a full adjacency.

D:

“OSPF area border routers convey inter-area network reachability using summary information” responds to another technical or business failure: A backbone-connected router receives intra-area LSAs but remote area destinations never appear in its routing table. That source case depends on: OSPF area border routers convey inter-area network reachability using summary information. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “Broadcast OSPF does not require every pair of DROthers to form a full adjacency” because Broadcast OSPF does not require every pair of DROthers to form a full adjacency.

Question 208

At fictional Juniper Publishing, a network engineer supporting hybrid offices is reviewing OSPF area design and link-state convergence during a new network integration (HCIP-H12-821-OSPF-052). The observed network issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. Which next engineering action best addresses the reported problem?

  1. Analyze Hello loss, Dead timers, interfaces errors and broadcast congestion rather than changing router IDs.
  2. Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements.
  3. Compare E1 versus E2 metric handling and evaluate route selection under competing exits.
  4. Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR.

Explanation

Correct Answer

D:

The directly responsive action is: Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR. The specific reported fault is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. Confirmation should show: The DROther pair remains 2-Way while each establishes proper Full adjacency with DR or BDR. The supporting technical principle is: Broadcast OSPF does not require every pair of DROthers to form a full adjacency.

Incorrect Answers

A:

“Analyze Hello loss, Dead timers, interfaces errors and broadcast congestion rather than changing router IDs” responds to another technical or business failure: An OSPF neighbor oscillates between Full and Down on a congested shared segment despite correct area IDs. That source case depends on: OSPF detects neighbor failure using liveness Hellos that can be impacted by packet loss. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR” because Broadcast OSPF does not require every pair of DROthers to form a full adjacency.

B:

“Align compatible totally stub area behavior at the ABR and validate permitted summary advertisements” responds to another technical or business failure: An OSPF totally stubby area receives unwanted detailed inter-area routes after only one router's configuration changes. That source case depends on: Totally stubby area behavior reduces inter-area summary visibility beyond ordinary stub restrictions. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR” because Broadcast OSPF does not require every pair of DROthers to form a full adjacency.

C:

“Compare E1 versus E2 metric handling and evaluate route selection under competing exits” responds to another technical or business failure: An engineer mistakes an OSPF external Type 2 metric for a path whose internal costs are always added to its advertised value. That source case depends on: OSPF E1 and E2 external cost calculations treat internal path costs differently. The present issue is: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. The more direct action is “Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR” because Broadcast OSPF does not require every pair of DROthers to form a full adjacency.

Question 209

At fictional Quayside Education, a network engineer supporting learning sites is reviewing OSPF area design and link-state convergence during an intersite service activation (HCIP-H12-821-OSPF-053). The observed network issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. Which observation most directly verifies that the corrective change succeeded?

  1. The NSSA prefix appears beyond the area as an appropriate translated external route.
  2. The backbone receives the intended external aggregate and required exceptions.
  3. The stub area has its intended default route without a flood of prohibited AS-external LSAs.
  4. The neighbor remains stable beyond multiple Dead intervals under normal traffic.

Explanation

Correct Answer

B:

The best verification observation is: The backbone receives the intended external aggregate and required exceptions. It demonstrates the corrective action: Configure appropriate ASBR external route summarization while preserving necessary exceptions. This fits the principle: OSPF external aggregation occurs at the appropriate redistribution boundary. Verify on the actual Huawei platform and network release.

Incorrect Answers

A:

“The NSSA prefix appears beyond the area as an appropriate translated external route” responds to another technical or business failure: An NSSA branch redistributes a local service prefix but the backbone never receives the route. That source case depends on: The best verification observation is: The NSSA prefix appears beyond the area as an appropriate translated external route. The present issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. The more direct action is “The backbone receives the intended external aggregate and required exceptions” because the best verification observation is: The backbone receives the intended external aggregate and required exceptions.

C:

“The stub area has its intended default route without a flood of prohibited AS-external LSAs” responds to another technical or business failure: A default route disappears inside an OSPF stub area because engineers expect external Type 5 LSAs to flood normally. That source case depends on: The best verification observation is: The stub area has its intended default route without a flood of prohibited AS-external LSAs. The present issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. The more direct action is “The backbone receives the intended external aggregate and required exceptions” because the best verification observation is: The backbone receives the intended external aggregate and required exceptions.

D:

“The neighbor remains stable beyond multiple Dead intervals under normal traffic” responds to another technical or business failure: Routers have the same network prefix but one side uses a different OSPF Hello interval on an Ethernet segment. That source case depends on: The best verification observation is: The neighbor remains stable beyond multiple Dead intervals under normal traffic. The present issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. The more direct action is “The backbone receives the intended external aggregate and required exceptions” because the best verification observation is: The backbone receives the intended external aggregate and required exceptions.

Question 210

At fictional Quayside Education, a network engineer supporting learning sites is reviewing OSPF area design and link-state convergence during an intersite service activation (HCIP-H12-821-OSPF-053). The observed network issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. Which next engineering action best addresses the reported problem?

  1. Inspect the external LSA forwarding address and the routing table's ability to resolve it.
  2. Apply compatible authentication settings and keys on both interfaces under controlled change.
  3. Configure appropriate ASBR external route summarization while preserving necessary exceptions.
  4. Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR.

Explanation

Correct Answer

C:

The directly responsive action is: Configure appropriate ASBR external route summarization while preserving necessary exceptions. The specific reported fault is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. Confirmation should show: The backbone receives the intended external aggregate and required exceptions. The supporting technical principle is: OSPF external aggregation occurs at the appropriate redistribution boundary.

Incorrect Answers

A:

“Inspect the external LSA forwarding address and the routing table's ability to resolve it” responds to another technical or business failure: An external OSPF route prefers the wrong exit because its forwarding address is unreachable or unexpected. That source case depends on: OSPF external route next-hop selection can use the LSA forwarding address when present. The present issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. The more direct action is “Configure appropriate ASBR external route summarization while preserving necessary exceptions” because OSPF external aggregation occurs at the appropriate redistribution boundary.

B:

“Apply compatible authentication settings and keys on both interfaces under controlled change” responds to another technical or business failure: An OSPF adjacency repeatedly fails due to mismatched authentication algorithms after a maintenance window. That source case depends on: OSPF routing exchanges depend on matched authentication parameters when authentication is enabled. The present issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. The more direct action is “Configure appropriate ASBR external route summarization while preserving necessary exceptions” because OSPF external aggregation occurs at the appropriate redistribution boundary.

D:

“Check whether the devices are both DROthers and validate adjacency with the elected DR or BDR” responds to another technical or business failure: Two OSPF routers on a broadcast VLAN stay at 2-Way and an engineer wrongly treats every such neighbor as failed. That source case depends on: Broadcast OSPF does not require every pair of DROthers to form a full adjacency. The present issue is: An ASBR advertising multiple external subnets floods excessive details because external route aggregation was never applied. The more direct action is “Configure appropriate ASBR external route summarization while preserving necessary exceptions” because OSPF external aggregation occurs at the appropriate redistribution boundary.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests